Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: CML8GX3M2A1600C9W how to set them working at 1600


07 Aug 2012   #11

Windows 7 Ultimate x64
 
 

Next step is to take it all al apart clean it and put it back together. After that I will set the memory manually at 1600 once again and see how it behaves.
I have to find time for all this though........


My System SpecsSystem Spec
.

08 Aug 2012   #12

Windows 7 Home Premium x64
 
 

Have you tried running memtest86 just to make sure there are no problems with the ram sticks, and if possible you could even try and see if you could borrow a friends ram sticks for a short ammount of time and if your getting BSOD with 3 different ram sets I would suspect its the motherboard
My System SpecsSystem Spec
08 Aug 2012   #13

Windows 7 Ultimate x64
 
 

I have run memtest and several other tests for the processor VGA card hard disk etc and all came out ok.
I used to think it was ram problem but since it continues with the new kit I think it the motherboard too.
I think it is time to buy a new one......
My System SpecsSystem Spec
.


08 Aug 2012   #14

Windows 7 Home Premium 64bit sp1
 
 

could be a bad memory controller did you ever update the bios or see if it has an update for better memory usage that tends to help situations like these

check your mainboard updates see if there is one for better memory usage

Also most Corsair I'ven seen is either 1.5 v Oc'ed can be turned up to 1.65v 1.2 is too low especially for overclocked ram make sure you have the right voltage rating that could be it as well

I would figure at 1.2 that is low
My System SpecsSystem Spec
08 Aug 2012   #15

Windows 7 Ultimate x64
 
 

I use the latest bios from gigabyte f13 beta and they confirmed that it is fully operational. They were supposed to have fixed the memory compatibility a few versions back.
My System SpecsSystem Spec
08 Aug 2012   #16

Windows 7 Home Premium 64bit sp1
 
 

This is a Quote about XMP

if you would like to know more here is the link [Solved] How does enabling XMP affect anything? - Memory - Motherboards-Memory

This is the best i can do without breaking rules

Hope it works out for you


Attached Thumbnails
CML8GX3M2A1600C9W how to set them working at 1600-quote.png  
My System SpecsSystem Spec
08 Aug 2012   #17

Windows 7 Ultimate x64
 
 

Thank you very much for the reply. I will try once more after I take my pc apart and put it back together.
If this fails I will buy new parts. I already started a research just to be prepared.
My System SpecsSystem Spec
11 Aug 2012   #18

Windows 7 Ultimate x64
 
 

Yesterday i opened my case took out the cooler and the processor cleaned it all up and put them back together.
When i use 8 gb of ram it always crashes. I used 4 sticks of 2 gb xms 3 (two ver 2.3 and two ver 6.0) which are included in my m/b's qvl list and 2 sticks of 4 gb vengeance lp white. The only way that i can make it work is when i use 4 gb only (2x2gb xms3 ver 2.3).
I tried several combinations in bios but whatever i do the system crashes.
So the system can work trouble free with only 4gb of ram?
Does this sound logical to you?
My System SpecsSystem Spec
11 Aug 2012   #19

Windows 7 Home Premium x64
 
 

Taken from their site

4 x 1.5V DDR3 DIMM sockets supporting up to 16 GB of system memory (Note 1)
Dual channel memory architecture
Support for DDR3 2600+/ 2200/1600/1333/1066/800 MHz memory modules
Support for non-ECC memory modules
Support for Extreme Memory Profile (XMP) memory modules
Go to Memory Support List for the latest memory support list.

So based on your info it makes no logic sense to me at all, there have to be something wrong most likely the motherboard
My System SpecsSystem Spec
11 Aug 2012   #20

Windows 7 Ultimate x64
 
 

This is the reason I started searching for a new mobo and processor.
It doesn't make sense to me either.
My System SpecsSystem Spec
Reply

 CML8GX3M2A1600C9W how to set them working at 1600




Thread Tools



Similar help and support threads for2: CML8GX3M2A1600C9W how to set them working at 1600
Thread Forum
Solved will ddr3 1600 run better then 1333 General Discussion
my ram (1600 mhz) is showing as 1066mhz Hardware & Devices
Revo 1600 - BSOD's BSOD Help and Support
wintv hvr 1600 no qam signal? Media Center
Hvr 1600 Drivers
how to make my memo run @ 1600 ? Performance & Maintenance
HP color laser jet 1600 Hardware & Devices

Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd

All times are GMT -5. The time now is 07:43 AM.
Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App
  

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33