Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: can i use 1333mhz ram on Intel g630?

22 Aug 2012   #1
Linsonav

Windows 7 Ultimate 32 bit
 
 
can i use 1333mhz ram on Intel g630?

I am planning to buy a cpu
Intel g630
asua p8h61 mlx 3
4gb ddr3 1333mhz
1 tb hdd
atx cabin
total Rs14000=$252 and is a budget pc to me

mobo supports both memory and g630 comes with 1066 support only(from ark intel and asus.com)
in Indian rural market 1333 is only common and 1066 very rare
1066 ram may be even low price but it is not available...
is there any problem or any decrease in performance?
1066 ram may be even low price but it is not available...what should i do?
thanks in advance


My System SpecsSystem Spec
.
23 Aug 2012   #2
paulpicks21

Windows 7 Professional 64 bit
 
 

There should be no issues what so ever running 1333mhz ram on that set up. It should run at full speed as well.

My i7 2600K CPU only supports 1333mhz but it runs 2133mhz just fine.
My System SpecsSystem Spec
23 Aug 2012   #3
Linsonav

Windows 7 Ultimate 32 bit
 
 

First of all Thank you
my prob is solved...but u said it can work in it's rated speed 1333
in my sys it shows only 1066(anyway its enough for me)...is ther any hope
My System SpecsSystem Spec
.

23 Aug 2012   #4
paulpicks21

Windows 7 Professional 64 bit
 
 

Sorry for my bad manners, welcome to sevenforums by the way

I am almost 100% sure it will work at it's rated speed. Like I say, all the 2nd Gen i7 CPU's only support upto 1333mhz but pretty much everyone on this forum that has one runs 1600mhz ram or over.

I know yours is not a 2nd gen i7, but the same rules apply, you should simply need to go into the bios once you have all your parts, set the ram speed to 1333mhz and make sure the timings and voltage are correct and it will work just fine.

The motherboard you have chosen supports 1333mhz ram, the cpu will not limit the ram to 1066. I am sure others will agree with me on here if anyone happens to read this.
My System SpecsSystem Spec
23 Aug 2012   #5
essenbe

Windows 7 Enterprise X64/Windows 10 Enterprise X64/Windows 10 Pro X64/Linux Mint
 
 

To the best of my knowledge, that is what all Sandy Bridge processors run stock, 1333. The memory controller is on the CPU not the board. 1st generation Sandy Bridge runs at 1333, stock.
My System SpecsSystem Spec
24 Aug 2012   #6
Linsonav

Windows 7 Ultimate 32 bit
 
 

Quote   Quote: Originally Posted by paulpicks21 View Post
Sorry for my bad manners, welcome to sevenforums by the way

I am almost 100% sure it will work at it's rated speed. Like I say, all the 2nd Gen i7 CPU's only support upto 1333mhz but pretty much everyone on this forum that has one runs 1600mhz ram or over.

I know yours is not a 2nd gen i7, but the same rules apply, you should simply need to go into the bios once you have all your parts, set the ram speed to 1333mhz and make sure the timings and voltage are correct and it will work just fine.

The motherboard you have chosen supports 1333mhz ram, the cpu will not limit the ram to 1066. I am sure others will agree with me on here if anyone happens to read this.

thanks again Paul....

actually i am new to forms.when i planned to take my new PC .i had the above confusion and searched google (like 1333 on 1066 in g630) one of the result was this
http://www.sevenforums.com/overclock...g-1333mhz.html
which you have answered...
in that i don't know more about ram timings and voltage,but i downloaded CPU z(in that thread that guy posted it) and run it..i post my CPU z result so that u can give me the timings volt and other setting to get1333 MHz...i see a lot of timings in timing table
also 1 more thing,in the CPU z ,bus speed is 100mhz...but ark Intel says it 5GT/s..should i change some other settings too? core speed is OK...when i load up the pc it gives it's rated speed from 1600mhz to 2700 mhz...but not bus speed has no change..
here is my cpu z result


Attached Thumbnails
can i use 1333mhz ram on Intel g630?-untitled.jpg  
My System SpecsSystem Spec
24 Aug 2012   #7
paulpicks21

Windows 7 Professional 64 bit
 
 

I would not mess with the bus speed, it is supposed to be 100 with sandybridge.

What exact ram did you buy? It should tell you the timings on the sticker on the ram. Failing that, looking at the cpuz shot I would say 9-9-9-24 would be a safe setting and the voltage should be 1.5V but again it should tell you that on the sticker.
My System SpecsSystem Spec
24 Aug 2012   #8
essenbe

Windows 7 Enterprise X64/Windows 10 Enterprise X64/Windows 10 Pro X64/Linux Mint
 
 

If you have the option on your board, to set the speed to 1333, change the timings to JDEC#3, 8-8-8-22-30 or if you have trouble JEDC#4, 9-9-9-24, which is usually safe.. You are running at 1066 now, but trust me, you will not see any performance increase if you change it. Only in benchmarks. The CPU bus speed is always 100MHz on Sandy Bridge. On some boards you can increase it a little, but that usually causes problems with other things. When you increase your bus speed, you also increase your ram, GPU and hard drive.
My System SpecsSystem Spec
Reply

 can i use 1333mhz ram on Intel g630?




Thread Tools Search this Thread
Search this Thread:

Advanced Search




Similar help and support threads
Thread Forum
RAM is not working on 1333Mhz
I have Corsair 4GB module, which is working on 1333MHz, but it's working on 1066 only. I got this module: Corsair Memory When I set ram freq. in BIOS on 1333MHz, pc is not starting. I got: Overclocking error. It's set on auto, and it's working on 1066MHz. Why I got this ? The mobo...
PC Custom Builds and Overclocking
Would RAM DDR3 1600MHz 1.65v run on 1333MHz 1.5V slot ?
Hi, as the title says my motherboard is a bit old which is ASRock G41C-S and its maximum support of RAM front side bus is 1333MHz, so i'm running 4GB of ram with two different modules one is A-Data 2GB DDR3 1333MHz and another is Apacer 2GB DDR3 1333MHz and i've ran them together for a year without...
Hardware & Devices
G Skill Ripjaws F3-10666CL9S-4GBRL 4GB DDR3 (1333MHz,Cas 9) timings ?
Hi i have G Skill Ripjaws F3-10666CL9S-4GBRL 4GB DDR3 (1333MHz,Cas 9) The timings that auto selct with my mobo are cas 7! however this causes programs to stop working,it doesnt crash the pc but crashes the program . What are the mem timings i should use this at, This is for another pc...
PC Custom Builds and Overclocking
8GB 1600Mhz + 4GB 1333Mhz
Would this work? Just that I may sell my 4GB sticks and was wondering if having 2x 4GB sticks at 1600Mhz would work with 2x 2GB sticks at 1333Mhz. Would they just lower down to 1333Mhz?
Hardware & Devices
DWL-g630 problem
My wireless network card don't work after i installed windows7 on my notebook . I was downloaded the lastest drivers for it and nothing. I can see my wireless card in "device manager" but with small yellow treeangle. Driver what i install is from windows7 site and for windows7...:confused:
Drivers
How to configure RAM to 1333MHz w/ P55 board (errors)
Hello, I've recently built a computer with i7-860, MSI P55-GD65 and the OCZ DDR3 PC3-10666 (OCZ3P1333LV4GK) RAM. When I start up my computer, my BIOS says 1066MHz. I don't know how I can obtain 1333MHz speeds. Do I need to configure it somehow? Also, when I run MemTest, I start getting...
Hardware & Devices


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 01:35.

Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App