Windows 7 repair disc not working?

Page 3 of 3 FirstFirst 123

  1. slickvicXLII
    Posts : 11
    windows 7 home SP1 64bit
    Thread Starter
       New #21

    karlsnooks said:
    Use IMGBURN at 4x to burn a CD.

    See if that works.

    How did you run Memtest86+?

    The Official ImgBurn Website
    That's what i've been using so far. used it at 4x for Memtest86+ and seatools. memory test burned fine, worked fine, and went through 7 passes with no errors. I also burned seatools two seperate times using that method, and got the issues i posted earlier. I made sure to double check the burn both times, and it burned the right way. I'll give it one more go if you think it'll help.

    edit: if you're still reading this thread, I just want to let you know that I won't be able to do anything more tonight. I should have more to add tomorrow. I just want to thank everyone that has taken the time out to help me. I definitely appreciate it.
    Last edited by slickvicXLII; 20 Aug 2012 at 19:37. Reason: just updating
      My Computer
    Quote Quote

  3. karlsnooks
    Posts : 10,200
    MS Windows 7 Ultimate SP1 64-bit
       New #22

    Well if you ran imgburn at 4x with verify, then cd should be good.

    You can try the disk in your working comuter.

    Won't harm anything.

    As requested, put your spec info into your System Specs. That procedure I gave explains how to enter the info.



    Will just make sure that the CD is good.
      My Computer
    Quote Quote

  4. F5ing
    Posts : 2,171
    Windows 7 Ultimate x64
       New #23

    slickvicXLII, you can fulfill Karl's request for specs if you've downloaded and loaded UBCD to a flash drive as recommended by Greg. There's an app under System called HWiNFO that'll identify your hardware components.

    The original UBCD for burning to CD can be found here: http://www.ultimatebootcd.com/download.html
      My Computer
    Quote Quote

  6. F5ing
    Posts : 2,171
    Windows 7 Ultimate x64
       New #24

    To kind of summarize all of your posts, the only thing your machine has been able to completely and successfully run is a test of memory by booting a CD that had Memtest86+ burned to it?

    I think I would pull that hard drive, install into another machine, and test it there. Sounds like it could very well have failed.

    Especially so if you've reset the BIOS already as Greg recommended.
      My Computer
    Quote Quote

  7. karlsnooks
    Posts : 10,200
    MS Windows 7 Ultimate SP1 64-bit
       New #25

    The disk should test the same in any machine IF the machine is good.

    This is why I'm thinking either power supply or motherboard problems.
      My Computer
    Quote Quote

  8. slickvicXLII
    Posts : 11
    windows 7 home SP1 64bit
    Thread Starter
       New #26

    Hey guys. I'm here with an update. I think you may be right about the harddrive. I tried booting from the hd just to try old repair options again, and now it says this:

    Check cable connection!
    PXE-MOF: Exiting Intel PXE ROM
    No bootable device -- insert boot disk and press any key.

    Even now when I try my repair disk, it gets stuck at a black screen with a mouse pointer in the center. Its weird though. My hd is still recognized by the bios and the seatools before it stops, and i've even retrieved files from it by booting from an Ubuntu Live CD. Could it just be a loose connection or something? Anyway I can test it and make sure? As stated earlier, seatools doesn't work, and my recovery disk doesn't boot anymore. Thanks in advance guys!
      My Computer
    Quote Quote

  10. F5ing
    Posts : 2,171
    Windows 7 Ultimate x64
       New #27

    The machine's BIOS might provide a test you can run on the drive.

    But if the drive is really going out I would quit trying to test it if you've still got data on there that you need to recover. See if you can copy out the rest of the data by using that Ubunu disk you were using. If the drive is really dying you may only have a few times left to access the data. You don't want to jeopardize that by wasting those last few available access attempts by trying to diagnose/repair it.

    You can check its connections after powering down, removing battery and AC power, hold down the power button for about 20 seconds to drain residual power, then opening the hard drive cover on the bottom of the machine. Be aware of static electricity.

    If the connections are good you can see if there's any HD testing facility in the machine's BIOS that you can run. If not you may have to pull the drive and test using another machine. Best would be attaching it directly to a desktop's motherboard via (S)ATA (allows full access to the drive's firmware). If you can't do that you can try using something like this for data recovery and/or limited testing:

    Amazon.com: SATA/PATA/IDE Drive to USB 2.0 Adapter Converter Cable for 2.5 / 3.5 Inch Hard Drive / Optical Drive with External AC Power Adapter: Computers & Accessories
      My Computer
    Quote Quote

 
Page 3 of 3 FirstFirst 123

  Related Discussions
Hello, my computer stopped booting up into Windows and kept doing the Startup Repair Tool. The error it is finding is not being fixed, so it takes me to the System Recovery Tools. I try to do System Restore, which does not work. So after searching around, I made a System Repair Disc from a work...
System Repair Disc Not working
in General Discussion

SYSTEM REPAIR DISC 6/2015 NOTE: My C: drive is a 256 GB SSD. I made a System Repair Disc on a new blank DVD-RW in accordance with instructions. I then tested it (in case I needed it). It did not produce a list of tools to repair the machine which is what I believe is the purpose of the disc....
As title says, when I try to burn a system repair disc the program stops working Problem signature: Problem Event Name: APPCRASH Application Name: recdisc.exe Application Version: 6.1.7600.16385 Application Timestamp: 4a5bc512 Fault Module Name: ole32.dll Fault...
Hello, i have a Acer Aspire 5755g-6841 laptop, and yesterday i started getting this message. "bootmgr is missing" after i tried to do a system restore. The attempt at the system restore ended bad with it not finishing and me having to reboot my laptop. It was stuck at 99% completion for 5hrs. Now...
I need some help, please. I couldn't find Windows 7 Repair Disc / Repair System / rewrite MBR for x64 Can you give me some advices, please ? Thank you
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

 © Designer Media Ltd
All times are GMT -5. The time now is 10:53.
Find Us