Windows 7 Forums

Showing results 1 to 15 of 15
Search took 0.00 seconds.
Search: Posts Made By: DevoDave
Forum: Hardware & Devices 07 Nov 2013
Replies: 10
Views: 820
Posted By DevoDave
You said your case fan was going out. Did you...

You said your case fan was going out. Did you make sure and unplug it? it could be causing a short or drawing lots of power. also check and recheck all your cable ends and make sure all your devices...
Forum: PC Custom Builds and Overclocking 02 Jan 2013
Replies: 13
Views: 998
Posted By DevoDave
There is a 101 things you can do to improve an...

There is a 101 things you can do to improve an overclock, but I strongly suggest you do a lot of research on the subject and a lot of research on your current hardware. It takes a lot of trial and...
Forum: PC Custom Builds and Overclocking 02 Jan 2013
Replies: 13
Views: 998
Posted By DevoDave
Looks pretty good to me!

Looks pretty good to me!
Forum: Performance & Maintenance 02 Jan 2013
Replies: 23
Views: 1,670
Posted By DevoDave
Have you defragmented your hard drive after your...

Have you defragmented your hard drive after your new install and updates? There is nothing worse than a 5400 rpm drive that's fragmented. Just make sure its plugged in and charge is full before you...
Forum: PC Custom Builds and Overclocking 02 Jan 2013
Replies: 13
Views: 998
Posted By DevoDave
Try using Hwmonitor from CPUID - System &...

Try using Hwmonitor from CPUID - System & hardware benchmark, monitoring, reporting (http://www.cpuid.com/softwares.html)
Forum: BSOD Help and Support 01 Jan 2013
Replies: 19
Views: 1,232
Posted By DevoDave
Try to keep your build as simple as possible....

Try to keep your build as simple as possible. Remove your graphics card and use the built in one instead. Leave in 1 stick of memory. disconnect anything you don't really need. This will help isolate...
Forum: PC Custom Builds and Overclocking 31 Dec 2012
Replies: 13
Views: 998
Posted By DevoDave
Well it looks like you are already running a 1:1...

Well it looks like you are already running a 1:1 ratio on the fsb/mem and you went from 2.4 to 3.2. id say that's about the best you are going see. besides lowering your latencies a bit, but I don't...
Forum: Graphic Cards 29 Dec 2012
Replies: 37
Views: 29,673
Posted By DevoDave
Hi Ramsayaaron Sounds like youre getting...

Hi Ramsayaaron

Sounds like youre getting close to the problem. I have seen this to many times and its almost always the same problem.

1: motherboards memory timings and voltage are incorrect...
Forum: Graphic Cards 16 Dec 2012
Replies: 103
Views: 5,229
Posted By DevoDave
Hi there, Just to troubleshoot. Try disabling...

Hi there,
Just to troubleshoot. Try disabling windows Aero theme and just use a basic theme and see if problem still occurs.
Forum: Sound & Audio 30 Oct 2012
Replies: 50
Views: 13,148
Posted By DevoDave
If you are blue screening try some of these...

If you are blue screening try some of these options

are you overclocking at all?

is your memory compatible with your board?

memory voltage within spec and timings? you can loosen the...
Forum: Sound & Audio 30 Oct 2012
Replies: 50
Views: 13,148
Posted By DevoDave
Another thing to try is boot to windows and...

Another thing to try is boot to windows and launch something playing music then disconnect your monitor cable all together and see if the noise persists through your usb headphones.
Forum: Sound & Audio 30 Oct 2012
Replies: 50
Views: 13,148
Posted By DevoDave
Can you try using a dvi cable to hook up to your...

Can you try using a dvi cable to hook up to your monitor instead of using the hdmi cable? So that the sound signal will not transfer to the the monitor at all, and if your using a tv/monitor, check...
Forum: Graphic Cards 17 Sep 2012
Replies: 37
Views: 29,673
Posted By DevoDave
And as far as your concerned I wasnt replying to...

And as far as your concerned I wasnt replying to your post. Just an hour ago you were also looking for suggestions. Well BUB you can install and uninstall your drivers all day long if you want or...
Forum: Graphic Cards 17 Sep 2012
Replies: 37
Views: 29,673
Posted By DevoDave
Go into your bios and look at your memory...

Go into your bios and look at your memory settings for your motherboards ram. Not video memory for the card. The first thing i would try is to raise the setting for tRFC. If it is like 60 or...
Forum: Hardware & Devices 06 Jul 2011
Replies: 25
Views: 8,473
Posted By DevoDave
Your problem sounds like your MCH voltage is to...

Your problem sounds like your MCH voltage is to low. Thats why it works fine with 2 sticks of ram vs 4. look in your bios and find out what your MCH voltage is. Try increasing it just a bit until it...
Showing results 1 to 15 of 15

 
Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 07:12 PM.
Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App
  

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33