Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Netmeter problem


01 Feb 2014   #1

Win 7 HP 64bit w/SP1
 
 
Netmeter problem

I have been using Netmeter for over 3 years and just started have a problem. Upon booting I get the following:

Netmeter.PNG

I have uninstalled (using Revo) and reinstalled - Same problem.

Installed to C:\Programs Files instead of Programs Files (x86) - No joy.

After a reinstall I have no problem for about 2 days (without rebooting) and then the above message appears and when I click OK the program shuts down.

Any suggestions?



Attached Images
 
My System SpecsSystem Spec
.

02 Feb 2014   #2

Microsoft Community Contributor Award Recipient

Windows 7 Home Premium x64 SP1
 
 

Boot into Safe Mode with Networking and see if the same problem occurs there. Which version are you using?

==- Readerror -==

A Guy
My System SpecsSystem Spec
02 Feb 2014   #3

Win 7 HP 64bit w/SP1
 
 

A Guy - Thanks for your reply. I rebooted into safe mode with network, and tried to start Netmeter. Got the same message as above. Using Netmeter v114 beta (I do not find anything later).

Any ideas?
My System SpecsSystem Spec
.


02 Feb 2014   #4

Microsoft Community Contributor Award Recipient

Windows 7 Home Premium x64 SP1
 
 

I have seen 2 major complaints while searching. One is the "Access violation", the other is "Nothing to monitor". Sometimes they are combined. Both mention removing additional/redundant ISATAP network interfaces. These problems also appear after installing VPN and programs like Teamviewer or Hamachi. Have a look at the post by hoakerk near the bottom of this discussion.

New NetMeter Beta Build 1.1.4

There are similar discussions about removing these additional interfaces. The trick is, which are redundant, and which are needed by IPV6, etc. I'd suggest making a full system image before making changes so you can revert to the last good step if something goes awry. If your ISP isn't using IPV6 now, you could conceivably have issues with that later, even if everything works fine now.

I'd recommend their forum, but I see posts from July with no replies.

Support (English)

A Guy
My System SpecsSystem Spec
03 Feb 2014   #5

Win 7 HP 64bit w/SP1
 
 

A Guy - Thanks for the links. I found that in device manager/file/options that there is a disk cleanup (see below). I click on apply and then started Netmeter. It started without the error message. I will mark this as solved but if I have further problems I will post here again.

Thanks again.


Attached Images
 
My System SpecsSystem Spec
03 Feb 2014   #6

Microsoft Community Contributor Award Recipient

Windows 7 Home Premium x64 SP1
 
 

Interesting! I hope that was it

A Guy
My System SpecsSystem Spec
10 Feb 2014   #7

Win 7 HP 64bit w/SP1
 
 

Just an update. After 1 week I have had no problems with Netmeter. Hope this helps someone else who is having the problem.
My System SpecsSystem Spec
Reply

 Netmeter problem




Thread Tools




Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd

All times are GMT -5. The time now is 07:59 AM.
Twitter Facebook Google+



Windows 7 Forums

Seven Forums Android App Seven Forums IOS App
  

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33