always getting failed updates, shows error code 80070057

Page 1 of 2 12 LastLast

  1. Posts : 43
    Windows 7 Home Premium 64bit
       #1

    always getting failed updates, shows error code 80070057


    hey everyone, i'm using windows 7 home premium, but when i want to update my windows it always failed, it says error code of 80070057 . but those occurs on update for hotfixes and security update, updates like ms silverlight and ms office ran just fine, why is that?

    sincerely,
    fadli
      My Computer


  2. Posts : 2,362
    Win7 H.Prem. 32bit+SP1
       #2

    Did you try Googling the error code.
      My Computer


  3. JMH
    Posts : 7,952
    Win 7 Ultimate 64-bit. SP1.
       #3

    fadlifari

    * Refer to the link below for Error code of 80070057

    update error code 80070057 - Microsoft Answers

    * Read this too...

    http://support.microsoft.com/kb/947821
      My Computer


  4. Posts : 43
    Windows 7 Home Premium 64bit
    Thread Starter
       #4

    i have already downloaded the windows 7 x64 system readiness tool and i have managed to install it. but it also the same fail when i tries to update my windows, even i have downloaded windows 7 SP 1 x64 (903 mb approx.) and i failed to install it, it says the error was "error data is invalid", did you happen to know why?

    thanks for your help :)
      My Computer


  5. JMH
    Posts : 7,952
    Win 7 Ultimate 64-bit. SP1.
       #5

    There is a list of troubleshooting steps to follow in the first link I sent you.
      My Computer


  6. Posts : 7,730
    Windows 7 Ultimate SP1 64-Bit
       #6

    Updates will fail if others are in progress at the same time.

    Check this Microsoft Support article in addition to the good information that Jan gave you.

    Support for Microsoft Update technical problems - troubleshooting

    Have a look at the Windows Update Log File as well.

    http://support.microsoft.com/kb/902093

    You might find this useful too.

    http://www.pcworld.com/article/15073...nt_update.html
      My Computer


  7. Posts : 43
    Windows 7 Home Premium 64bit
    Thread Starter
       #7

    why does when i want to do sfc /scannow it says windows resource protection could not perform the requested operation? it is stuck on 12%
      My Computer


  8. Posts : 43
    Windows 7 Home Premium 64bit
    Thread Starter
       #8

    here is the details of failed updates its only 2 that i have attached, the real is so many updates were failed.
    always getting failed updates, shows error code 80070057 Attached Files
      My Computer


  9. JMH
    Posts : 7,952
    Win 7 Ultimate 64-bit. SP1.
       #9

    * Please refer to the following 2 tutorials & see what you think.

    Repair Install

    Clean Install Windows 7

    * Have you a System Backup prior to your current set of problems?

    * Have you a windows 7 Disk?

    * Alternatively you could seek Microsoft Tech's Support.
    I believe the email service is free.
    Click on the below link.

    Please Verify your Location
      My Computer


  10. Posts : 2,362
    Win7 H.Prem. 32bit+SP1
       #10

    fadlifari said:
    hey everyone, i'm using windows 7 home premium, but when i want to update my windows it always failed, it says error code of 80070057 . but those occurs on update for hotfixes and security update, updates like ms silverlight and ms office ran just fine, why is that?

    sincerely,
    fadli
    It could be a stuck MSI installer. Open a command prompt and run as administrator. type
    reg delete HKLMSOFTWAREMicrosoftSQMClient WindowsDisabledSessions /va /f using copy/paste then hit enter, close command prompt and reboot. Now try the updates again.
      My Computer


 
Page 1 of 2 12 LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 06:36.
Find Us