A Rebuild Gone Bad

Page 7 of 10 FirstFirst ... 56789 ... LastLast

  1. Posts : 11,424
    Windows 7 Ultimate 64
       #61

    Lollies,
    In my estimation your likely still fine with the Corsair 850 as it's a premium PSU with thoughtfully designed rail supplies. But more is always better.....but I would be totally surprised that this turned out to be the 850's issue.
      My Computer


  2. Posts : 302
    Windows 7 Ultimate x64
    Thread Starter
       #62
      My Computer


  3. Posts : 398
    Windows 7 Ultimate x64
       #63

    Yes? that would be a standoff lol separates motherboard from case...
      My Computer


  4. Posts : 302
    Windows 7 Ultimate x64
    Thread Starter
       #64

    TonyTiger2004 said:
    Yes? that would be a standoff lol separates motherboard from case...
    The stand-offs were already in place. It's not just lying inside of it touching everything.
      My Computer


  5. Posts : 11,424
    Windows 7 Ultimate 64
       #65

    Lollies if the stand off's where already in place......where they in the correct place? One off in another place or an extra stand off added could be as bad as none in place.....it only takes one short to smoke something. I'm not saying this is the case here but maybe you could tell us how the standoffs came to be already screwed in? Who did it and did they get checked, did all the mobo screws go in and tighten properly. Of note though is if this was the case with your build it would have smoked up right away not a monitor change later !
      My Computer


  6. Posts : 302
    Windows 7 Ultimate x64
    Thread Starter
       #66

    linnemeyerhere said:
    Lollies if the stand off's where already in place......where they in the correct place? One off in another place or an extra stand off added could be as bad as none in place.....it only takes one short to smoke something. I'm not saying this is the case here but maybe you could tell us how the standoffs came to be already screwed in? Who did it and did they get checked, did all the mobo screws go in and tighten properly. Of note though is if this was the case with your build it would have smoked up right away not a monitor change later !
    They are molded into the case itself, the holes just line up with the motherboard. If that was the case everything would be out anyways.
      My Computer


  7. Posts : 11,424
    Windows 7 Ultimate 64
       #67

    Understand, that's good and not the issue.
      My Computer


  8. Posts : 302
    Windows 7 Ultimate x64
    Thread Starter
       #68

    I want to try an older card and see if that works because I have found a few posts about people with Asus boards who upgrade to the 580 and have the same problem. This is only after they upgrade from a different card. May or may not be the problem but I have no additional card and my friend is anal so I can't use his.
      My Computer


  9. Posts : 398
    Windows 7 Ultimate x64
       #69

    Lollies said:
    I want to try an older card and see if that works because I have found a few posts about people with Asus boards who upgrade to the 580 and have the same problem. This is only after they upgrade from a different card. May or may not be the problem but I have no additional card and my friend is anal so I can't use his.
    Are the latest bios installed on your asus board by chance? i may have asked already but as this thread is growing its hard remember what we have and havn't tried. But i would convince ur buddy into letting u use his vido card, wont hurt it.
      My Computer


  10. Posts : 3,187
    Main - Windows 7 Pro SP1 64-Bit; 2nd - Windows Server 2008 R2
       #70

    What computer are you posting from, Lollies? Can you snag the card out of it?
      My Computer


 
Page 7 of 10 FirstFirst ... 56789 ... LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 08:55.
Find Us