Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.

Windows 7: BSOD after OS re-installation

23 May 2011   #1

Windows 7 Professional 32-bit (Upgrade)
BSOD after OS re-installation

Hello! I have recently encountered multiple BSODs over the last few days. I initially thought that it was OS related, and my first course of action was to re-install Windows 7 Professional 32-Bit. Unfortunately, I am still suffering the same BSOD issues I had prior OS re-installation. I had just finished my 2nd re-install today when I suffered another BSOD crash! This system was initially built in April 2007, with upgrades to RAM, Video Card, and Hard drive over the last 18 months. After researching these symptoms, I must assume that this is a hardware related issue. Any help you can provide in tracking down the source of my problems, would be greatly appreciated! Required file attachments attached below.

My System SpecsSystem Spec
24 May 2011   #2

Windows 10 Pro x64, Arch Linux

The problem may lie in your CPU
Check if your CPU is properly seated in the socket and ensure that it is not overheating

This test below will tell us if your CPU is defective or not
information   Information
Run Prime 95 again to test your CPU.. Carefully the instructions in this tutorial: CPU - Stress Test with Prime95. Run 3 separate tests, one on each of the settings (Blend, Small FFTs, Large FFTs). Post back with your results.

Stop 0x124 - what it means and what to try

*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *

Use !analyze -v to get detailed debugging information.

BugCheck 124, {0, 85b4f01c, b2000040, 800}

Probably caused by : hardware

A fatal hardware error has occurred. Parameter 1 identifies the type of error
source that reported the error. Parameter 2 holds the address of the
WHEA_ERROR_RECORD structure that describes the error conditon.
Arg1: 00000000, Machine Check Exception
Arg2: 85b4f01c, Address of the WHEA_ERROR_RECORD structure.
Arg3: b2000040, High order 32-bits of the MCi_STATUS value.
Arg4: 00000800, Low order 32-bits of the MCi_STATUS value.

Debugging Details:

OVERLAPPED_MODULE: Address regions for 'CTEXFIFX' and 'CTEXFIFX.SYS' overlap

BUGCHECK_STR:  0x124_GenuineIntel





8c9088ac 82c27f3f 00000124 00000000 85b4f01c nt!KeBugCheckEx+0x1e
8c9088e8 82d1ef04 86464c31 85b4f01c 82cb84f0 hal!HalBugCheckSystem+0xab
8c908918 82c281f1 85b50d48 82c35e40 00000000 nt!WheaReportHwError+0x230
8c908a2c 82c282e3 85b50d48 85b50d98 00000004 hal!HalpMcaReportError+0x3b
8c908a50 82c283ff 00000000 85b50d98 00000000 hal!HalpMceHandler+0x8b
8c908a70 82c28548 00000000 85b50d48 8c908b90 hal!HalpMceHandlerWithRendezvous+0x4b
8c908a80 82c1e5f5 00000000 00000000 00000000 hal!HalpHandleMachineCheck+0x34
8c908b90 82c1b261 0000001b 8c903750 00000000 hal!HalpMcaExceptionHandler+0x87
8c908b90 00000000 0000001b 8c903750 00000000 hal!HalpMcaExceptionHandlerWrapper+0x89


FOLLOWUP_NAME:  MachineOwner

MODULE_NAME: hardware

IMAGE_NAME:  hardware



BUCKET_ID:  0x124_GenuineIntel_PROCESSOR_BUS

Followup: MachineOwner
My System SpecsSystem Spec

 BSOD after OS re-installation

Thread Tools

Similar help and support threads
Thread Forum
Windows 7 installation compatibility report- remove installation disc
I am trying to install Windows 7 on my laptop. When I click on "upgrade" it takes me to a compatibility report that says "the computer started using the windows installation disc. Remove the installation disc and restart your computer so that windows starts normally." When I remove the disc and try...
General Discussion
BSOD on new Win 7 installation.
Hello there forum, upon returning to my pc I found a dialog box stating "windows had just recovered from an unexpected shutdown". As to what I was doing before this happened I can't answer because I left my pc to take a nap and upon resuming from sleep mode I was greeted with this message. May I...
BSOD Help and Support
BSOD in XP Installation
Hi, would appreciate if someone fixes this asap... I want to dual boot my system (Sony VAIO VGN-NS25G) with Windows XP. I can't use Virtual Machines because my CPU doesn't support Hardware Virtualization. So my only choice was to dual boot Windows XP. I created a 25GB partition (off Disk...
BSOD Help and Support
BSOD during Installation
I've tried installing Windows 7 build 6801 and I keep getting a BSOD during the installation. I have a 186GB HD and I've partitioned it the following way: 93.1GB - Vista 58.1GB - XP 20GB - for 7 15GB - Debian and they're all primary partitions. My XP partition used to be 78.1GB, but I resized...
BSOD Help and Support

Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 03:37.
Twitter Facebook