Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.

Windows 7: Problem with blue screen (windows 7 ultimate 32bit)

20 Dec 2011   #1

windows 7 ultimate 32bit
Problem with blue screen (windows 7 ultimate 32bit)

Hello, i instaled to my pc windows 7 ultimate 32bit before a week. Everything was ok until blue screnn apears. Pc crash for few seconds and bluescreen apears. It hapens only when i a going to play tha game TRINE. I play tha game normally and then 5 minutes pc crashes , bluescreen and restart.

BCCode: 1000007e
BCP1: C0000005
BCP2: 92145F37
BCP3: 8C5F59D4
BCP4: 8C5F55B0
OS Version: 6_1_7601
Service Pack: 1_0
Product: 256_1

Please tell me where is the problem..
My hardware is :

Motherboard: DFI LANParty UT nF4 SLI-DR Expert
CPU: DualCore AMD Athlon 64 X2, 2400 MHz (12 x 200) 4800+
GPU: Point of view NVIDIA GeForce 7800 GTX (512 MB)
Audio: Realtek ALC850 (AC'97) onboard card
Hard Disk: Seagatte Baracuda ST3120813AS ATA Device (120 GB, 7200 RPM, SATA-II)
RAM: OCZ 2x1 GB DDR SDRAM PC3200 EL Platinum Dual Channel (OCZ4002048ELPE)

I will upload the .dmp i hope will help this. Thank you and sorry for my english!
My System SpecsSystem Spec
20 Dec 2011   #2

Windows 10 Pro x64, Arch Linux

Run some hardware tests,
NVIDIA/AMD Video Card - Test with OCCT
RAM - Test with Memtest86+

Run Prime 95 to test your CPU. Carefully the instructions in this tutorial: CPU - Stress Test with Prime95. Run 3 separate tests, one on each of the settings (Blend, Small FFTs, Large FFTs). Post back with your results.
Note that this test may overheat the CPU, ensure proper cooling

Remove IObit Smart Defrag, it has compatibility issues with Windows 7

Update your Marvell Yukon 88E8056 PCI-E Gigabit Ethernet Controller driver
Marvell - Support - Driver Downloads

Post back with your results
Is your version of Windows 7 genuine?
yk62x86.sys        0x9201f000    0x9206f000    0x00050000    0x49a2b642    23/02/2009 18:44:18
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *

This is a very common bugcheck.  Usually the exception address pinpoints
the driver/function that caused the problem.  Always note this address
as well as the link date of the driver/image that contains this address.
Some common problems are exception code 0x80000003.  This means a hard
coded breakpoint or assertion was hit, but this system was booted
/NODEBUG.  This is not supposed to happen as developers should never have
hardcoded breakpoints in retail code, but ...
If this happens, make sure a debugger gets connected, and the
system is booted /DEBUG.  This will let us see why this breakpoint is
Arg1: c0000005, The exception code that was not handled
Arg2: 92145f37, The address that the exception occurred at
Arg3: 8c5f59d4, Exception Record Address
Arg4: 8c5f55b0, Context Record Address

Debugging Details:

EXCEPTION_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.

92145f37 8b5104          mov     edx,dword ptr [ecx+4]

EXCEPTION_RECORD:  8c5f59d4 -- (.exr 0xffffffff8c5f59d4)
ExceptionAddress: 92145f37 (dxgmms1!VIDMM_DEVICE::ReferenceCommitment+0x00000029)
   ExceptionCode: c0000005 (Access violation)
  ExceptionFlags: 00000000
NumberParameters: 2
   Parameter[0]: 00000000
   Parameter[1]: 00000074
Attempt to read from address 00000074

CONTEXT:  8c5f55b0 -- (.cxr 0xffffffff8c5f55b0)
eax=84d0c2d0 ebx=8623d000 ecx=00000070 edx=00000060 esi=84dc8fe0 edi=84d0c2a0
eip=92145f37 esp=8c5f5a9c ebp=8c5f5aa0 iopl=0         nv up ei ng nz na po nc
cs=0008  ss=0010  ds=0023  es=0023  fs=0030  gs=0000             efl=00010282
92145f37 8b5104          mov     edx,dword ptr [ecx+4] ds:0023:00000074=????????
Resetting default scope




ERROR_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.



READ_ADDRESS: GetPointerFromAddress: unable to read from 829a2848
Unable to read MiSystemVaType memory at 82981e20

92145f37 8b5104          mov     edx,dword ptr [ecx+4]



LAST_CONTROL_TRANSFER:  from 9213ebf7 to 92145f37

8c5f5aa0 9213ebf7 84d0c2a0 84ee4044 8623d000 dxgmms1!VIDMM_DEVICE::ReferenceCommitment+0x29
8c5f5ab8 921409be 00000000 84d0c2a0 00000001 dxgmms1!VIDMM_GLOBAL::ReferenceAllocationForSubmission+0x67
8c5f5bb8 92157850 96501d40 00000000 84d90210 dxgmms1!VIDMM_GLOBAL::PrepareDmaBuffer+0xa68
8c5f5d18 92158141 84d33f08 84da4828 8c5f5d3c dxgmms1!VidSchiSubmitRenderCommand+0x1c0
8c5f5d28 921583de 84d33f08 82870509 86227350 dxgmms1!VidSchiSubmitQueueCommand+0x61
8c5f5d3c 92158485 86227350 00000000 8623c410 dxgmms1!VidSchiRun_PriorityTable+0x24
8c5f5d50 82a41fda 86227350 ad2a219e 00000000 dxgmms1!VidSchiWorkerThread+0x7f
8c5f5d90 828ea1f9 92158406 86227350 00000000 nt!PspSystemThreadStartup+0x9e
00000000 00000000 00000000 00000000 00000000 nt!KiThreadStartup+0x19


SYMBOL_NAME:  dxgmms1!VIDMM_DEVICE::ReferenceCommitment+29

FOLLOWUP_NAME:  MachineOwner

MODULE_NAME: dxgmms1

IMAGE_NAME:  dxgmms1.sys


STACK_COMMAND:  .cxr 0xffffffff8c5f55b0 ; kb

FAILURE_BUCKET_ID:  0x7E_dxgmms1!VIDMM_DEVICE::ReferenceCommitment+29

BUCKET_ID:  0x7E_dxgmms1!VIDMM_DEVICE::ReferenceCommitment+29

Followup: MachineOwner
My System SpecsSystem Spec

Thread Tools

Similar help and support threads
Thread Forum
Blue screen problem on windows Ultimate 64 bit
Please help i am getting blue screen ....suddenly will u please tell me wats going wrong
BSOD Help and Support
Problem with Windows 7 Ultimate 32bit installing.
Hi to every one! I'm Artan and i have a old Fujitsu Siemens PC Scenic BS015 with a P 4 2.8 GHz. and 3 GB DDR with HDD 37.2 GB. Was installed on it the Windows 7 Ultimate 32 bit. I find another HDD of 37.2 GB and i put on to extend dhe HDD. After some times the PC was not working well and I...
Installation & Setup
Windows 7 32bit ultimate Freezes after login screen
I would like if someone can please help me out with an issue i am currently facing. I try to start up windows after entering my password at the screen it loads for a while then i am faced with my desktop background and icons show up. If i move my mouse cursor to the bottom taskbar to click start it...
BSOD Help and Support
Sound Problem Under Windows 7 Ultimate 32bit
Dear forum members, i'm a Regular windows user since Windows XP SP2. few months ago i upgrade to Windows 7 ultimate (32 bit). i have onboard sigmatel sound card which works under Windows XP SP2/SP3 without any issue after installing sigmatel audio driver for Windows XP. but it's not working under...
Sound & Audio

Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd

All times are GMT -5. The time now is 08:43.
Twitter Facebook