BSOD 0x00000024 related to USB eLiscenser driver?

Page 1 of 2 12 LastLast

  1. Posts : 16
    Windows 7 Home Premium x64
       #1

    BSOD 0x00000024 related to USB eLiscenser driver?


    Hey, I've gotten 2 BSOD 24 errors while having my USB eLiscenser software up within 30 minutes. I'll usually get an error from the Liscener software and then my computer screen will go fuzzy for a second and then a really loud noise comes out of my speakers and the BSOD 24 error pops upe

    Here are the memory dumps
    Please tell me any other information you might need to help me. This error occurs pretty often if I have the software up but I haven't tested my computer without it.

    I just finished reinstalling my operating system today because I thought that might be the solution to this problem but that didn't work. They start occuring again right after I installed the eLiscenser diver again. All my drivers are up to date.

    Note: I NEED this software. I use it to open Cubase 6 which is a program used to record music and I cannot go without it. Having it is a MUST!

    Thanks for your help.

    System Specs:
    OS: Windows 7 Home Premium x64
    CPU: AMD Phenom II 4x 955 Black Edition
    Motherboard: ASUS M4A88T-M
    Memory: 8GB DDR3 Ballistix
    Graphics Card: XFX ATI Radeon HD 5870
    Last edited by RushPfeiffer; 08 Jun 2012 at 23:16.
      My Computer


  2. Posts : 10,200
    MS Windows 7 Ultimate SP1 64-bit
       #2
      My Computer


  3. Posts : 16
    Windows 7 Home Premium x64
    Thread Starter
       #3

    Ah missed that little part, thanks.

    Editted my post.
      My Computer


  4. Posts : 11,269
    Windows 7 Home Premium 64 Bit
       #4

    Security Software: ??? Make sure to install security software. I recommend either of these:

    After installing your security software, update it, and then run full scans today with each program. Report back the results of the scans.


    Make sure to install all Windows Updates. I see you do not have Service Pack 1 installed:


    Your crashes primarily indicate hard disk problems. This could mean hard disk corruption, bad sectors, a failing hard disk, Windows files or registry corruption, viruses, or memory problems.
    • If you are overclocking any hardware, please stop.

    • Run Disk Check with both boxes checked for all HDDs and with Automatically fix file system errors checked for all SSDs. Post back your logs for the checks after finding them using Check Disk (chkdsk) - Read Event Viewer Log (you may need to search for wininit instead of chkdsk).
      For any drives that do not give the message:
      Windows has checked the file system and found no problems
      run disk check again as above. In other words, if it says:
      Windows has made corrections to the file system
      after running the disk check, run the disk check again.

    • Run the short and long tests with SeaTools for HDDs.
    • If you have an SSD, make sure the following are up to date:
      • SSD firmware
      • BIOS Version
      • Chipset Drivers
      • Hard disk controller drivers/SATA drivers
      • If you have a Marvell IDE ATA/ATAPI device, uninstall it in device manager and see if the system performs better.


    • Check Windows for corruption. Run SFC /SCANNOW Command - System File Checker up to three times to fix all errors with a restart in between each. Post back if it continues to show errors after a fourth run or if the first run comes back with no integrity violations. Use OPTION THREE of SFC /SCANNOW Command - System File Checker to provide us with the sfcdetails.txt file if errors occur.

    • Download and install Malwarebytes, update it, do not start the free trial, and then run a full scan. Also run a full scan with your antivirus software installed on your system. If you do not have antivirus software installed, see the Good and Free system security combination. for better security steps and scanning tools. Make sure to update the security software before running the full scan.

    • Run the boot version of Memtest86+ paying close attention to Parts 2 and 3 of the tutorial. Also, in case Memtest86+ misses anything and comes up with no errors, run the extended version of the Windows Memory Diagnostics Tool for at least five passes. These you may want to run overnight since they take a long time to complete (run them an hour before bed each of the next two nights and check before going to sleep that they are still running).
         Warning
      Before you proceed with the following, answer these two questions: Are you still under warranty? Does your warranty allow you to open up the machine to check hardware? If you are unsure of the answers to these questions, contact your system manufacturer. WARNING: The steps that follow can void your warranty!!!

      For Part 3: If You Have Errors: If you swap any memory components, follow these steps for ESD safety:
      1. Shut down and turn off your computer.
      2. Unplug all power supplies to the computer (AC Power then battery for laptops, AC power for desktops)
      3. Hold down the power button for 30 seconds to close the circuit and ensure all power drains from components.
      4. Make sure you are grounded by using proper grounding techniques, i.e. work on an anti-static workbench, anti-static desk, or an anti-static pad. Hold something metallic while touching it to the anti-static surface, or use an anti-static wristband to attach to the anti-static material while working. If you do not have an anti-static workbench, desk, or pad, you can use your computer tower/case by finding a metal hold in it, such as a drive bay.

      Once these steps have been followed, it is safe to remove and replace components within your computer.
      My Computer


  5. Posts : 16
    Windows 7 Home Premium x64
    Thread Starter
       #5

    I just did the Memory test and got alot of errors in the memory so I just replaced both my RAM sticks for a fast solution to see if it would work. Working good so far, I'll post back if any other problem occur or if I don't have any.
      My Computer


  6. Posts : 11,269
    Windows 7 Home Premium 64 Bit
       #6

    Alright, good steps. Thanks for updating us. :)

    Look forward to finding out the outcome.
      My Computer


  7. Posts : 16
    Windows 7 Home Premium x64
    Thread Starter
       #7

    It seems I got rid of the BSODs but I started getting lockups 15-20 minutes after bootup so I replaced my motherboard to fix this issue and it seems to be running perfectly again. Will check back in.

    Reason for replacing my motherboard instead of CPU or GPU was because I had 2 bad RAM ports in my motherboard and I was having very strange problems with USB ports and what not, So I figured replacing the Motherboard would be the smartest idea.
      My Computer


  8. Posts : 11,269
    Windows 7 Home Premium 64 Bit
       #8

    Nice troubleshooting!

    Let us know if you need anything further or if you determine the problem is indeed solved. :)
      My Computer


  9. Posts : 16
    Windows 7 Home Premium x64
    Thread Starter
       #9

    Ok I just got a error 0x00000050 BSOD

    I have replaced my RAM
    Replaced my Motherboard
    Reinstalled my operating system.


    So it's either hard drive or GPU most likely

    And no I don't have any viruses, I have not gone on any suspicious sites or downloaded anything weird or opened any suspicious emails. I do have Malware Bytes on my computer and I do have Service pack 1.


    I'm a computer tech myself so please don't give me suggestions to update software. Becuase 5 day old software WILL NOT cause a BSOD. and if it did half the world would have BSODs lol.


    I attached the Dump. Thank you!
      My Computer


  10. Posts : 11,269
    Windows 7 Home Premium 64 Bit
       #10

    Security Software: ??? Make sure to install security software. I recommend either of these:

    After installing your security software, update it, and then run full scans today with each program. Report back the results of the scans.


    Recommend removing your ASUS utilities through Start Menu -> Control Panel -> Uninstall a program. They can provide software interfaces with the hardware for overclocking, and even when the overclock is not enabled, that interface can cause instability.


    Update the following driver:
    Code:
    synusb64.sys Fri Jun 26 07:30:11 2009 (4A44CD63)
    The above is your SIA Syncsoft USB protection software. If you cannot find an update for it, I would recommend removing it.


    Crashes point to memory. We should check your RAM compatibility. Download and install CPU-Z and Upload screenshots of the CPU, Mainboard, Memory, and SPD tabs. In the SPD tab, upload an image of each slot.
      My Computer


 
Page 1 of 2 12 LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 10:37.
Find Us