BSOD when monitor went into standby

Moteo · 24 Aug 2013

Hello everyone this could be nuthing but i just wanted to make sure. Anyway was sitting infront the computer a few minutes ago i wasnt doing anything so it was idle an the monitor went into standby. all of sudden i hear this beep an the computer shut it self off. Turned it back on there was a windows recovery error screen! i used windows seven diagnostic to generate the files for you guys!!! Any help or advice would be great to put my mind at ease. Thanks

Arc · 24 Aug 2013

Hello Moteo.

The BSOD is caused by MotioninJoy simulate Xbox 360 controller virtual Xinput device.

Code:

*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck D1, {fffff88005fa9638, 2, 8, fffff88005fa9638}

*** WARNING: Unable to verify timestamp for MijXfilt.sys
*** ERROR: Module load completed but symbols could not be loaded for MijXfilt.sys
Probably caused by : MijXfilt.sys ( MijXfilt+1b638 )

Followup: MachineOwner
---------

And the driver is old by an year.

Code:

fffff880`05f8e000 fffff880`05fb0000   MijXfilt T (no symbols)           
    Loaded symbol image file: MijXfilt.sys
    Image path: \SystemRoot\system32\DRIVERS\MijXfilt.sys
    Image name: MijXfilt.sys
    Timestamp:        Sat May 12 09:57:12 2012 (4FADE6A0)
    CheckSum:         00022009
    ImageSize:        00022000
    Translations:     0000.04b0 0000.04e4 0409.04b0 0409.04e4

Search for possible updates in MotioninJoy simulate Xbox 360 controller(virtual Xinput device) | MotioninJoy. Apply it. Let us know the results.

Moteo · 25 Aug 2013

Thanks million arc will update it right away!

Arc · 25 Aug 2013

You are welcome mate :)
Let us know if the issue persists.

Moteo · 26 Aug 2013

So i unistalled it downloaded the lastest version...an it happen again. you wanna take a look at it agian for me?? Thanks

Arc · 26 Aug 2013

Actually you had the latest one ... and so the update did nothing change there. The situation after update is as same as the previous ......

Code:

fffff880`05f1a000 fffff880`05f3c000   MijXfilt T (no symbols)           
    Loaded symbol image file: MijXfilt.sys
    Image path: \SystemRoot\system32\DRIVERS\MijXfilt.sys
    Image name: MijXfilt.sys
    Timestamp:        Sat May 12 09:57:12 2012 (4FADE6A0)
    CheckSum:         00022009
    ImageSize:        00022000
    Translations:     0000.04b0 0000.04e4 0409.04b0 0409.04e4

And the BSOD is caused by the same old module, MotioninJoy simulate Xbox 360 controller virtual Xinput device.

Code:

*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck D1, {fffff88005f35638, 2, 8, fffff88005f35638}

*** WARNING: Unable to verify timestamp for MijXfilt.sys
*** ERROR: Module load completed but symbols could not be loaded for MijXfilt.sys
Probably caused by : MijXfilt.sys ( MijXfilt+1b638 )

Followup: MachineOwner
---------

At that situation, mate, I have only one thing to suggest you. Stop using MitionInJoy. Opt for any other XBOX controller. May be a wired one.

Moteo · 26 Aug 2013

well this is the first time this has happended...an i have been using it for quite a while it was pretty cool allowed me to use my ps3 pad as an xbox one!! i guess they mite fix it with the next update!! just a question i know there tutorials if not to much hassle wat did u look at out of all them files the programme created?? i take it u opened them with notepad??

Arc · 26 Aug 2013

We open the dump files with Debugging Tools for Windows.

Moteo · 26 Aug 2013

Am gunna look in to that so i dont i dont have to hassle you guys!! Any way just to let you since i uninstalled it all going well :) thank you

Arc · 26 Aug 2013

You are welcome mate :)
If any help is needed, let us know.