BSOD playing FFXIV ARR, hal.dll error 0x00000124

Page 2 of 3 FirstFirst 123 LastLast

  1. Posts : 3,056
    Windows 10
       #11

    Thanks, keep us posted.
      My Computer


  2. Posts : 13
    Win 7 Premium 64bit
    Thread Starter
       #12

    Screenshots


    Here are the before and during load screenshots.
      My Computer


  3. Posts : 3,056
    Windows 10
       #13

    The temperatures looks (too) good .
    For how long did the tests run?
      My Computer


  4. Posts : 13
    Win 7 Premium 64bit
    Thread Starter
       #14

    YoYo155 said:
    The temperatures looks (too) good .
    For how long did the tests run?
    Maybe 5 minutes. I had already run them both previously for longer periods of time (30-60 minutes) and captured the results in the initial posts. Max temp was the GPU and that was 69F.
      My Computer


  5. Posts : 3,056
    Windows 10
       #15

    5 minutes is not enough :\.
    You want to stress the components not only in terms of test the cooling but also in terms of
    stability of operation under full-load. The goal is find the failing hardware.


    Fill out this form and post back the result:



    Putting load on the PC using Prime95 for the CPU side and Furmark for the GPU.
    Don't forget to tick the 'Round off checking' option under Advanced:
    Reset the BIOS back to default in case you're unaware that your CPU is overclocked:

       Note

    Write down the current value of the SATA Mode!
    Its either AHCI or IDE.
    After resetting the CMOS go back and verify the value for SATA Mode is what it was
    when the OS was installed.
      My Computer


  6. Posts : 13
    Win 7 Premium 64bit
    Thread Starter
       #16

    YoYo155 said:
    5 minutes is not enough :\.
    You want to stress the components not only in terms of test the cooling but also in terms of
    stability of operation under full-load. The goal is find the failing hardware.


    Fill out this form and post back the result:



    Putting load on the PC using Prime95 for the CPU side and Furmark for the GPU.
    Don't forget to tick the 'Round off checking' option under Advanced:
    Reset the BIOS back to default in case you're unaware that your CPU is overclocked:

       Note

    Write down the current value of the SATA Mode!
    Its either AHCI or IDE.
    After resetting the CMOS go back and verify the value for SATA Mode is what it was
    when the OS was installed.
    Yes, I understand that and as I mentioned I ran the tests already and posted the results in my initial post. I've also done the calculator for psu prior to this issue and I was under the 500w that my psu provides. I checked it again for completion sake and it is 411w.
      My Computer


  7. Posts : 3,056
    Windows 10
       #17

    juiceisloose said:
    Yes, I understand that and as I mentioned I ran the tests already and posted the results in my initial post. I've also done the calculator for psu prior to this issue and I was under the 500w that my psu provides. I checked it again for completion sake and it is 411w.
    Thanks.
    411W out of 500W on 5 years old PSU is a lot to ask as components deteriorate faster
    when they are run close to the top end of their spec.
    Do you have a different PSU you can install for testing purposes?

    Also your hard-drive is of 160GB capacity, those models are usually from 2008 and prior
    which makes it very old, I suggest testing the HDD.
    Code:
    Model    WDC WD1600AAJS-22PSA0 ATA Device
    Size    149.05 GB (160,039,763,968 bytes)
    Testing the HDD:

    1. Perform a Disk Check | Disk Check
    2. Then Post the results following | THIS METHOD
    3. Download SeaTools for Windows if you don't want to use a CD to test the HDD you can use YUMI – Multiboot USB Creator to create a bootable USB (instructions are found at the bottom of both pages).
    4. If SeaTools for Windows is unable to recognize your HDD visit HDDdiag and follow the instructions.



    How did you test the RAM?
    What program did you use and for how many consecutive passes did you let it run for?
      My Computer


  8. Posts : 13
    Win 7 Premium 64bit
    Thread Starter
       #18

    YoYo155 said:
    juiceisloose said:
    Yes, I understand that and as I mentioned I ran the tests already and posted the results in my initial post. I've also done the calculator for psu prior to this issue and I was under the 500w that my psu provides. I checked it again for completion sake and it is 411w.
    Thanks.
    411W out of 500W on 5 years old PSU is a lot to ask as components deteriorate faster
    when they are run close to the top end of their spec.
    Do you have a different PSU you can install for testing purposes?

    Also your hard-drive is of 160GB capacity, those models are usually from 2008 and prior
    which makes it very old, I suggest testing the HDD.
    Code:
    Model    WDC WD1600AAJS-22PSA0 ATA Device
    Size    149.05 GB (160,039,763,968 bytes)
    Testing the HDD:

    1. Perform a Disk Check | Disk Check
    2. Then Post the results following | THIS METHOD
    3. Download SeaTools for Windows if you don't want to use a CD to test the HDD you can use YUMI – Multiboot USB Creator to create a bootable USB (instructions are found at the bottom of both pages).
    4. If SeaTools for Windows is unable to recognize your HDD visit HDDdiag and follow the instructions.



    How did you test the RAM?
    What program did you use and for how many consecutive passes did you let it run for?
    Ran Memtest for the full time as indicated earlier in a post. Zero errors.

    Will run checkdisk next.
      My Computer


  9. Posts : 13
    Win 7 Premium 64bit
    Thread Starter
       #19

    YoYo155 said:
    juiceisloose said:
    Yes, I understand that and as I mentioned I ran the tests already and posted the results in my initial post. I've also done the calculator for psu prior to this issue and I was under the 500w that my psu provides. I checked it again for completion sake and it is 411w.
    Thanks.
    411W out of 500W on 5 years old PSU is a lot to ask as components deteriorate faster
    when they are run close to the top end of their spec.
    Do you have a different PSU you can install for testing purposes?

    Also your hard-drive is of 160GB capacity, those models are usually from 2008 and prior
    which makes it very old, I suggest testing the HDD.
    Code:
    Model    WDC WD1600AAJS-22PSA0 ATA Device
    Size    149.05 GB (160,039,763,968 bytes)
    Testing the HDD:

    1. Perform a Disk Check | Disk Check
    2. Then Post the results following | THIS METHOD
    3. Download SeaTools for Windows if you don't want to use a CD to test the HDD you can use YUMI – Multiboot USB Creator to create a bootable USB (instructions are found at the bottom of both pages).
    4. If SeaTools for Windows is unable to recognize your HDD visit HDDdiag and follow the instructions.



    How did you test the RAM?
    What program did you use and for how many consecutive passes did you let it run for?
    Finished Chkdsk I believe no errors found. Attached log file.
      My Computer


  10. Posts : 3,056
    Windows 10
       #20

    Thanks for the update :) .

    The CHKDSK looks to be in order, did you manage to test the RAM and the HDD using Seatools (or WDLG) yet?
      My Computer


 
Page 2 of 3 FirstFirst 123 LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 06:51.
Find Us