BSOD Memory_management, Bad_pool_header, etc.

Hi Mikle190. Sorry for this unexceptional late reply.

Code:

*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 1A, {8887, fffffa8001b95e80, fffffa8001b95b80, 501}

Probably caused by : hardware_ram ( ZEROED_PAGE_CORRUPTED )

Followup: MachineOwner
---------

Test your RAM modules for possible errors.
How to Test and Diagnose RAM Issues with Memtest86+
Run memtest for at least 8 passes, preferably overnight.

If it start showing errors/red lines, stop testing. A single error is enough to determine that something is going bad there.

Let us know the results.

It is good to know that the RAM is OK :)

The Kaspersky issue will be over by a single uninstallation and reinstallation.

Next step .... enable Driver Verifier to monitor the drivers.
Driver Verifier - Enable and Disable
Run Driver Verifier for 24 hours or the occurrence of the next crash, whichever is earlier.

   Information

Why Driver Verifier:
It puts a stress on the drivers, ans so it makes the unstable drivers crash. Hopefully the driver that crashes is recorded in the memory dump.

How Can we know that DV is enabled:
It will make the system bit of slow, laggy.

   Warning

Before enabling DV, make it sure that you have earlier System restore points made in your computer. You can check it easily by using CCleaner looking at Tools > System Restore.

If there is no points, make a System Restore Point manually before enabling DV.

   Tip

• If you fail to get on the Desktop because of DV, Boot into Advanced Boot Options > Safe mode. Disable DV there. Now boot normally again, and try following the instruction of enabling DV again.
• If you cannot boot in Safe mode too, do a System Restore to a point you made earlier.

Let us know the results, with the subsequent crash dumps, if any. Post it following the Blue Screen of Death (BSOD) Posting Instructions.

Boot into Safe Mode, then disable verifier. Uninstall these two:

• Itunes
• Daemon Tools

Daemon Tools, Alcohol 120% and Power Archiver Pro uses SCSI Pass Through Direct (SPTD), which is a well known BSOD causer. Uninstall Daemon Tools at first. Then download SPTD standalone installer from Disk-Tools.com, and execute the downloaded file as guided below :

• Double click to open it.
• Click this button only:
• 
• If it is grayed out, as in the picture, there is no more SPTD in your system, and you just close the window.

Then restart and boot the computer back in normal mode. Use it normally. Let us know how it is running there.
_________________________________________________________________________________

Code:

*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck C9, {23e, fffff88005e58360, fffff98006732ee0, 0}

Unable to load image \SystemRoot\system32\DRIVERS\GEARAspiWDM.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for GEARAspiWDM.sys
*** ERROR: Module load completed but symbols could not be loaded for GEARAspiWDM.sys
*** WARNING: Unable to verify timestamp for dtsoftbus01.sys
*** ERROR: Module load completed but symbols could not be loaded for dtsoftbus01.sys
Probably caused by : dtsoftbus01.sys ( dtsoftbus01+1360 )

Followup: MachineOwner
---------

Daemon tools can cause any issue, and when it is combined with itunes it is almost an evil

But I doubt that it is the only reason behind the "Hardware RAM" error we got from the crash dumps. Let us wait and see what happens next.

Disable verifier.

Install Service pack 1 and all other windows updates. Otherwise the system will remain vulnerable to threats.
Learn how to install Windows 7 Service Pack 1 (SP1)
Service Pack and Update Center - Microsoft Windows

Install the NVIDIA DRIVERS 314.22WHQL only.

• Uninstall All nvidia items in Control Panel > Programs and features
  
  • 3D Vision Control Driver
  • 3D Vision Driver
  • Graphics Driver
  • HD Audio Driver
  • PhysX
  • nvidia Update
  
  (Are you using nvidia chipset drivers? If so, dont uninstall anything other than those are listed).
• Now follow Drivers - Clean Left over Files after Uninstalling
• Download 314.22 WHQL. While installing, Select Custom (Advanced) install. In the next page, follow this settings:
  
  

Let the computer run normally, without DV enabled. Let us know how it is running.