New
#31
gregrocker,
Will you check this, please?
windows and ubuntu won't boot after bsod, possible virus
Why is nothing marked active?
This ol' dog got to get some Zzzzzzsss....
.
Last edited by cottonball; 02 Jan 2015 at 01:35.
gregrocker,
Will you check this, please?
windows and ubuntu won't boot after bsod, possible virus
Why is nothing marked active?
This ol' dog got to get some Zzzzzzsss....
.
Last edited by cottonball; 02 Jan 2015 at 01:35.
None of that looks familiar to me, It almost looks like an entirely different drive. Both my Linux and windows disks are marked active in disk management and I'm currently trying to mark the linux drive inactive as gregrocker requested.
exeviss, assign a drive letter to the partition to mark it Inactive.
Cottonball, the drive you pictured is an EFI system on a GPT disk, which have no Active flags or MBR.
Only on an MBR disk, the Active flag points to the System partition intended to boot Win7. If it is moved it must have the System boot files (signified by the System flag) moved as well or it won't boot. During the moving of the System boot files, the System partition is also made bootable using bootsect which is why it requires a process and not just copying the files:
Startup Repair - Run 3 Separate Times
Bootmgr - Move to C:\ with EasyBCD - Windows 7 Forums
Thanks gregrocker! Was wondering about that...couldn't tell it was an Extensible Firmware Interface (EFI) on a GUID Partition Table (GPT) disk. I have not kept up with all of this.Cottonball, the drive you pictured is an EFI system on a GPT disk, which have no Active flags or MBR.
It seems I'm not able to assign a drive letter to any of the linux partitions because they are not ntfs. The option is greyed out in disk management.
edit: Maybe I'm using the wrong guide
Drive Letter - Add, Change, or Remove in Windows
Will EasyBCD remove the active flag? Reformatting to ntfs is kind of a hassle
Last edited by exeviss; 02 Jan 2015 at 12:56. Reason: posted wrong link, fixed
exeviss,
The Linux file system is not supported by windows.
To my understanding, Windows can’t read Linux partitions without third-party software.
In Disk Management, can I assume that Disk 1 is all Ubuntu?
Are you trying to remove the Active flag on the 18.63 GB (Active, Primary Partition)?
yes disk one is 100% ubuntu. I'm just going to remove the drive while I do repairs.
An option is running the Diskpart commands to set the Ubuntu partition inactive:
Start the computer, and tap the F8 key until you get to the Advanced Boot Options menu
Use the arrow keys to select the Repair your computer menu item
From there...
Select your language settings, and click: Next
Select your User account and click: OK (If you did not set a password, leave blank.)
On the System Recovery Options you get the following options:
Startup Repair
System Restore
Windows Complete PC Restore
Windows Memory Diagnostic Tool
Scan your computer's memory for errors
Command Prompt
Select: Command Prompt
Press ENTER after you type in each of these commands (in red) (not case sensitive):
DISKPART (to open the partition utility)
LIST DISK (disk number(s) shown)
1 (select disk: 1 where Ubuntu is contained, if that is the case)
LIST PARTITION (partition numbers shown)
n (where n is the number of the Primary partition you wish to make Inactive)
INACTIVE (the selected partition on the selected disk is made Inactive)
EXIT (to exit DiskPart)
EXIT (to exit the Command Prompt)
Restart the computer, and go to Disk Management. Is the Partition inactive?
.
Someone who knows Linux will have to say for sure if it could/should have an Active partition, as it could be misreporting by Disk Mgmt which normally can't even show Linux partitions.
If Diskpart can't work then just unplug the drive while doing the repairs. Later you can plug that drive in alone to make it bootable using GRUB, or if you want to add it to a Windows Dual Boot menu follow Dual boot Ubuntu-Win7
I'm sorry I'm swamped here with installs for friends before I change coasts so am only able to check infrequently.
I'm trying to go through the bootrec.exe steps again with the ubuntu drive unplugged. Now I'm getting a message I didn't get before. When I run
ren c:\boot\bcd bcd.old
it tells me that a duplicate file name exists or the file can not be found. Duplicate would make sense because I already went through these steps before. Should I modify it to another name? if so how?
edit: found this post
BCD missing status:0xc000000f & Diskpart won't list my main partition
so "ren c:\boot\bcd bcd.old2" is what I want right? I was thinking "ren c:\boot\bcd bcd2.old" but I didn't want to just guess so I googled what I thought the command could be.
Last edited by exeviss; 02 Jan 2015 at 18:22. Reason: found possible solution with google fu