BSOD On Computer with Clean Wipe. Help!

Hi Wolfeii.

Test your RAM modules for possible errors.

How to Test and Diagnose RAM Issues with Memtest86+

Run memtest86+ for at least 8 consecutive passes.

If it start showing errors/red lines, stop testing. A single error is enough to determine that something is going bad there.

If it does not show any error, enable Driver Verifier to monitor the drivers.

Driver Verifier - Enable and Disable

Run Driver Verifier for 24 hours or the occurrence of the next crash, whichever is earlier.

   Information

Why Driver Verifier:
It puts a stress on the drivers, ans so it makes the unstable drivers crash. Hopefully the driver that crashes is recorded in the memory dump.

How Can we know that DV is enabled:
It will make the system bit of slow, laggy.

   Warning

Before enabling DV, make it sure that you have earlier System restore points made in your computer. You can check it easily by using CCleaner looking at Tools > System Restore.

If there is no points, make a System Restore Point manually before enabling DV.

   Tip

• If you fail to get on the Desktop because of DV, Boot into Advanced Boot Options > Safe mode. Disable DV there. Now boot normally again, and try following the instruction of enabling DV again.
• If you cannot boot in Safe mode too, do a System Restore to a point you made earlier.

Let us know the results, with the subsequent crash dumps, if any.
_________________________________________

Code:

BugCheck 3B, {c0000005, fffff80002dc30a1, fffff8800ecff110, 0}

Probably caused by : ntkrnlmp.exe ( nt!SeComputeQuotaInformationSize+9 )

Followup: MachineOwner
---------

Code:

BugCheck 1A, {5003, fffff70001080000, 3201, 7feff27e009}

Probably caused by : ntkrnlmp.exe ( nt! ?? ::FNODOBFM::`string'+295b1 )

Followup: MachineOwner
---------

Check individual sticks in different slots to ascertain if it is a faulty stick or a faulty slot on the mobo but chances are you will need new RAM or have to remove one faulty stick to regain stability

Pauly said:

Check individual sticks in different slots to ascertain if it is a faulty stick or a faulty slot on the mobo but chances are you will need new RAM or have to remove one faulty stick to regain stability

Now follow the "Part 3: If You Have Errors:" of How to Test and Diagnose RAM Issues with Memtest86+

Errors/red lines means one or more RAM is faulty. But the fault may occur due to a faulty DIMM slot, too, which is a motherboard component. Using memtest86+, you can discriminate between a faulty RAM and a faulty motherboard.

How? Say you have two RAM sticks and two DIMM slots. You obtained errors at the test with all RAM sticks installed. Now, remove all the sticks but one. Test it in all the available slots, one by one. Continue the same procedure for all the available sticks.
How to make the inference that is it a RAM issue or it is a motherboard issue? Suppose you have got the result like that:

No code has to be inserted here.

It is a RAM, a bad RAM.

But if you have got a result like that:

No code has to be inserted here.

It is a motherboard issue. The particular slot is bad.

If it is a bad RAM, you need to change the RAM. Take the other existing (good) RAM to the shop and get one of the exactly same specification. The best is, get a totally new RAM KIT.

If it is a bad slot, it is a motherboard issue. But changing the motherboard needs a preparation for most of us; so dont populate that slot for the time being.

Wolfeii said:

Well I only have one stick of ram but after switching the slot and testing I already have one error and it's only on the first pass. So do I need new ram still or do I need more testing?

No. Get the RAM replaced.

Wolfeii said:

What's interesting to note is that it seems that there are less errors on the second test than there was on the first after I swapped them

You will not want to concentrate on the error count. A single error is enough.

OK, no problem.