Method 1 – Adjust Paging File
To start off, you can try a simple trick with the paging file that fixes the issue for some folks. If the issue is not hardware related, then this page file solution might just work.
First, open the
Control Panel and click on
System. You can also right-click on
Computer or
This PC and choose
Properties.
Now click on the
Advanced System Settings link on the left hand side.
Under
Performance, click on the
Settings button.
Click on the
Advanced tab and then click on the
Change button under the
Virtual Memory heading.
Finally, we have reached where we need to be. Uncheck the
Automatically manage paging file size for all drives box and then select
No paging file.
Click OK several times to get out of all the dialog windows and then restart your computer. Once you are back in, follow the exact steps again shown above, but this time select
System managed size and check the
Automatically manage paging file size for all drives box.
Like I said earlier, this works for some people, but not others so your mileage will vary. If you’re still getting blue screens, keep reading.
Method 2- Check Disk
This error can also occur if your hard drive is either failing or has errors on the drive. One quick way to check the hard drive is to run the
chkdsk command in Windows.
To do this, click on Start and type in
cmd. Right-click on the top result and choose
Run as Administrator.
At the prompt, type in the following command:
chkdsk /f If you get a message stating the drive is locked and if you would like to schedule a chkdsk on the next restart, type in
Y for yes. Go ahead and restart your computer and allow chkdsk to run, which could take a long time on Windows 7 and earlier. The process is much faster on Windows 8 and Windows 10.
Method 3 – Bad Driver
If you recently updated a driver for a piece of hardware on your computer, it could be a faulty driver causing the blue screen issue.
Drivers are essential for Windows, but sometimes the latest drivers can cause more problems than they fix.
If you are using
third-party to automatically update your PC drivers, it’s probably a good idea to configure the software so that you can review each driver that is going to be updated beforehand.
Anyway, you can try to fix this problem by clicking on Start and typing in
Device Manager. Right-click on the device that you updated the driver for and select
Roll Back Driver. You can also choose
Properties and then go to the
Driver tab and click the
Roll Back Driver button.
If the button is disabled or you don’t see the option when you right-click on a device, that means the current driver is the only driver ever installed for that device.
One last thing you can try is to click the
Uninstall button and restart your computer. Windows will automatically try to install the driver for the hardware when Windows reboots. If this didn’t work, try the next method.
Method 4 – Last Known Config
In some cases, the issue is bigger than just a driver and will require using the
Last Known Good Configuration feature in Windows.
This basically brings back an older version of the entire Windows registry that worked. In Windows 7 and earlier, you just have to press the F8 key in order to bring up the
Advanced Options screen when booting up.
In Windows 8 and Windows 10, check out my post on
how to load the System Recovery Options screen since the F8 key no longer works on those two operating systems.
In addition to trying Last Known, you should also try to do a System Restore if Last Known didn’t work. Check out my previous post on how to
perform a system restore.
Method 5- Check RAM
As mentioned above, RAM is usually the main culprit when it comes to this error. Usually, it means the RAM has become defective. Most computers will have multiple RAM chips installed and you can sometimes fix the problem by just removing the bad chip and leaving the rest in.
If you think there is a problem with the memory, visit your computer manufacturer’s website and download the manual for upgrading RAM on your computer.
The guide will usually tell you how to open the computer and where to look for the RAM. If you have more than one RAM chip, pop one out and then turn on your computer. If the blue screen goes away, then you took out the bad one. If not, switch and try again.
If you only have one RAM chip, then you need to purchase another RAM chip as you can’t run the computer without at least one RAM chip.
Method 6 – Anti-virus Software
In some rare cases, your anti-virus software can be causing the blue screen errors. I recommend uninstalling your anti-virus program completely and then restarting the computer.
The chances are quite small that any software will cause this error, but it’s worth a shot at this point, especially if you are using an anti-virus product from a smaller lesser-known company.
Quote