Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Replaced CPU/PSU still get BSODs

18 Nov 2009   #1
mpohutsk

Windows 7
 
 
Replaced CPU/PSU still get BSODs

Here's my latest batch of minidumps. Any ideas?


My System SpecsSystem Spec
.
18 Nov 2009   #2
torrentg

7600.20510 x86
 
 

Hey.

Well, to start with, you have a 0x1A error which is described as
"Internal memory management structures are corrupted. To further investigate the cause, a kernel memory dump file is needed."

Another is a 0x24 error.

Wait, let me stop here for a moment. You have all different assorted varieties of errors.

So what we are going to do is the following. Open an elevated command prompt and run this command for each partition you have, changing C each time for the partition:

chkdsk /r C:

Then completely uninstall any antivirus and firewall applications.

Then, open another elevated command prompt and run this in it:

sfc /scannow


These drivers are old and should be Googled and updated to newest possible:

fet6x64 fet6x64.sys Thu Jun 19 07:40:18 2008
speedfan speedfan.sys Sun Sep 24 09:26:48 2006


I'd also check that the Vdimm (Ram voltage) and timings and set correctly for the modules you're using. You can visit the manufacturer's page of the RAM and find the specific model. Then adjust your bios accordingly.

Then run Memtest overnight to see if any errors are shown.



-------------------------

After you've done these things, please post any new bsod dumps and we can look at them to see what else we can do.
My System SpecsSystem Spec
19 Nov 2009   #3
thefabe

Windows 7 ultimate 64 bit / XP Home sp3
 
 

MY 2 cts worth memtest download Memtest86+ - Advanced Memory Diagnostic Tool and information on running it. Fabe Memory Diagnostics
My System SpecsSystem Spec
.

19 Nov 2009   #4
mpohutsk

Windows 7
 
 

Quote   Quote: Originally Posted by torrentg View Post
I'd also check that the Vdimm (Ram voltage) and timings and set correctly for the modules you're using. You can visit the manufacturer's page of the RAM and find the specific model. Then adjust your bios accordingly.
Ok so my ram timings are 5-5-5-15-2T and voltage is supposed to be 2.1. The BIOS on my motherboard allows me to set the 5-5-5-15 (which it actually defaults at) but it defaults the voltage at 1.8. It will not let me change the 2T (there's not even a setting for it) and there's also a bunch of additional settings for RAM timings that I can't get information on.

Also, I don't even know what fet6x64.sys is, or how to update or remove it. I just got rid of speedfan, I don't need it anyway. Did the command prompts and nothing came up as bad.
My System SpecsSystem Spec
19 Nov 2009   #5
thefabe

Windows 7 ultimate 64 bit / XP Home sp3
 
 

Whenever I'm looking for all the timing settings I usually go to the Ram manufacturers web site. They are usually pretty good at letting you know the recommended, tested timings and voltages for your ram and MB. You can go to the Corsair site here The Corsair Support Forums - Powered by vBulletin
My System SpecsSystem Spec
19 Nov 2009   #6
chev65

Windows 7 Ult, Windows 8.1 Pro,
 
 

Try these settings.
Use the yellow slots on your board if running two sticks.

REF cycle time from 40 to 60 depending on frequency used.
NB voltage 1.26V "very important"
Memory voltage 2.1
DRAM OC Charger enabled
DRAM Training enabled
DRAM Static read enabled
Ai clock twister light

Also take your Dram timing control off Auto so that you can adjust timings 5 5 5 15 2T. You won't get anywhere using the 1T setting.

AI overclock tuner switch from Auto to Manual. "Settings won't stick unless you do this."

You have to adjust these settings manually or there is no way your board will run stable.

Let me know if these settings work.
My System SpecsSystem Spec
19 Nov 2009   #7
zigzag3143

Win 8 Release candidate 8400
 
 

Quote   Quote: Originally Posted by mpohutsk View Post
Here's my latest batch of minidumps. Any ideas?

Hi and welcome

You dmps fall in 2 categories. First MEMORY, second system files. The memory may be causing the system files to fail

I would
download and run memtestx86 and run it overnight.
I would also run a system file check by typing cmd in search>right click and run as admin> SFC /SCANNOW

Let us know the results

If you are overclocking stop
If you have a raid update the driver

Ken J++



Microsoft (R) Windows Debugger Version 6.11.0001.404 X86
Copyright (c) Microsoft Corporation. All rights reserved.


Loading Dump File [C:\Users\K\Desktop\111809-17862-01.dmp]
Mini Kernel Dump File: Only registers and stack trace are available

Symbol search path is: SRV*d:\symbols*Symbol information
Executable search path is:
Windows 7 Kernel Version 7600 MP (2 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS Personal
Built by: 7600.16385.amd64fre.win7_rtm.090713-1255
Machine Name:
Kernel base = 0xfffff800`02c56000 PsLoadedModuleList = 0xfffff800`02e93e50
Debug session time: Wed Nov 18 22:15:26.471 2009 (GMT-5)
System Uptime: 0 days 1:51:11.048
Loading Kernel Symbols
...............................................................
................................................................
.........................
Loading User Symbols
Loading unloaded module list
......
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck A, {28, 2, 0, fffff80002d0a090}

Probably caused by : memory_corruption ( nt!MiFindNodeOrParent+0 )


Followup: MachineOwner

Hope this helps

Ken J++
---------
My System SpecsSystem Spec
20 Nov 2009   #8
mpohutsk

Windows 7
 
 

Quote   Quote: Originally Posted by chev65 View Post
Try these settings.
Use the yellow slots on your board if running two sticks.

REF cycle time from 40 to 60 depending on frequency used.
NB voltage 1.26V "very important"
Memory voltage 2.1
DRAM OC Charger enabled
DRAM Training enabled
DRAM Static read enabled
Ai clock twister light

Also take your Dram timing control off Auto so that you can adjust timings 5 5 5 15 2T. You won't get anywhere using the 1T setting.

AI overclock tuner switch from Auto to Manual. "Settings won't stick unless you do this."

You have to adjust these settings manually or there is no way your board will run stable.

Let me know if these settings work.
Ok these settings seemed to have stabilized the system. If I get another BSOD I'll post the minidump.
My System SpecsSystem Spec
20 Nov 2009   #9
mpohutsk

Windows 7
 
 

Blah. Spoke too soon. Here's the newest one. By the way, I ran Memtest86+ after I changed the RAM settings and it made 3 passes no problems.
My System SpecsSystem Spec
20 Nov 2009   #10
torrentg

7600.20510 x86
 
 

Quote   Quote: Originally Posted by mpohutsk View Post
Blah. Spoke too soon. Here's the newest one. By the way, I ran Memtest86+ after I changed the RAM settings and it made 3 passes no problems.
Unfortunately, even a clear run overnight is not indicative of perfect memory. The longer you run it, the more conclusive it is, however. It is still technically possible for RAM to be defective with clear passes indefinitely, too.

On the fortunate side of things, the bsod looks to be from a faulty driver trying to write to a read only part of memory.

If you know what this process is, update it: "BackgroundDown" (Or could be a virus - scan with multiple scanners.)

These are the older drivers you have so I'd try to get these updated and see how it goes:

ASACPI ASACPI.sys Sun Mar 27 22:30:36 2005
ctac32k ctac32k.sys Wed Jul 02 04:38:22 2008
fet6x64 fet6x64.sys Thu Jun 19 07:40:18 2008
Rt64win7 Rt64win7.sys Thu Feb 26 04:04:13 2009

You could possibly look at these too:

amdxata amdxata.sys Tue May 19 13:56:59 2009
spldr spldr.sys Mon May 11 12:56:27 2009
ctsfm2k ctsfm2k.sys Wed Jun 03 13:57:30 2009
ctoss2k ctoss2k.sys Wed Jun 03 13:57:43 2009
ctprxy2k ctprxy2k.sys Wed Jun 03 13:59:48 2009
ha20x2k ha20x2k.sys Wed Jun 03 13:59:09 2009
emupia2k emupia2k.sys Wed Jun 03 13:57:22 2009
CT20XUT CT20XUT.SYS Wed Jun 03 14:01:05 2009
CTHWIUT CTHWIUT.SYS Wed Jun 03 14:01:09 2009
CTEXFIFX CTEXFIFX.SYS Wed Jun 03 14:01:00 2009
My System SpecsSystem Spec
Reply

 Replaced CPU/PSU still get BSODs




Thread Tools




Similar help and support threads
Thread Forum
BSOD 0x116 (stop error) Replaced GPU, replaced RAM, replaced PSU
My monitor goes black and I am forced to reboot. After rebooting I get a blue screen prompt telling me that i've recovered from a BSOD. I've been monitoring them since October. In October, I RMA'd my graphics card. Oct 27. You can see that after I got a new GPU, my BSOD's halted... so...
BSOD Help and Support
Replaced Motherboard Mutliple BSODs (Stop codes + dmp files attatched)
Hello All! sorry for vague title, I didn't want to make multiple threads taking up space. This is my first post, I read how to post, I'm a little tired and I apologize if I missed something. I recently replaced my mother board to a MSI X58a-GD45 I did format and re-install windows and I keep...
BSOD Help and Support
Can you check if RAM has been replaced?
Hi, My sister bought a new computer from a company, it was a toshiba C660 something or other. It runs windows 7 home premium 64bit. When it first arrived it constantly BSODed, I tried all I could to diagnose the problem but in the end it seemed that getting a new one sent out would be the safest...
Hardware & Devices
OEM W7 and replaced mobo
Hello. Never even had a chance to get PC online and register and found out my asus mobo was faulty. I did installed OEM W7, however. What consequences, if any, do I know face as a result of swapping out mobo's? (activation wise?) I do plan on wiping the HDD drive and reinstalling windows, unless...
Windows Updates & Activation
Just Replaced My ASUS Motherboard And Now Random BSODs!!! HELP!
Hello. Replaced my motherboard with the same make and model under a warrranty program with ASUS. The motherboard is the P5Q. I did not have these issues at the last moments of using the original P5Q before sending it to ASUS. I noticed this issue right from the start after connecting the necessary...
BSOD Help and Support
Replaced motherboard...
My old motherboard stopped working, so while it's getting repaired, I decided to swap it with another one (different model). The problem is, Windows 7 won't boot anymore. I get a blue screen of death and the system keeps rebooting. Now I know replacing a motherboard with an old install is not a...
General Discussion


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 10:53.
Twitter Facebook Google+ Seven Forums iOS App Seven Forums Android App