Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Recurrent BSODs while imaging with Macrium, or just using new printer

1 Week Ago   #11
axe0

Windows 10 Pro
 
 

Although you don't really have bad sectors that cannot be handled, I believe that there may be other issues with the drive(s) that cannot be identified as much as we'd like to. For this reason I recommend to replace at least the drive where the long test in SeaTools failed, the one where the short drive self test failed is up to you, all I see is an issue that the drive can easily handle.


My System SpecsSystem Spec
.
6 Days Ago   #12
Clairvaux

Windows 7 Home Premium 64-bit (OEM)
 
 

Thank you for looking into that data, axe0. Let me throw in a few questions.
  • Is there a particular concern associated with the deep dips in transfer rate shown by the Benchmark test of HD Tune, especially since they happen at different places on the disk each time the test is run ?
  • Those dips happen on the system disk. They don't happen on the data disk, which you advise to change because it failed the Sea Tools DOS test. Is it unexpected they should not happen on the data disk, which is the one with a bad sector ? Or is it an unconnected phenomenon ?
  • I use HD Disk Sentinel. Do you have any opinion on that program, especially compared to HD Tune ?
  • HD Disk Sentinel has some repair options which could be applied to one, or both of the disks. One is destructive of data, the other possibly so. Do you think it might be worth trying them ?
  • Given the state of the disks, how reliable are my Macrium Reflect images (which are always set to verify themselves) ? Is there a possibility that they carry over some defects to a new disk ?
  • Is it possible that the failed printer installation has anything to do with the problem ? Or is it unconnected ?
Added info : both disks have been used daily since the beginning of 2011.
My System SpecsSystem Spec
6 Days Ago   #13
axe0

Windows 10 Pro
 
 

1. There's no concern in my opinion, a test can sometimes show deep dips when a drive has been used for some time. Typically this happens only once, and even though multiple tests has shown them it is still no concern.

2. Your disk can handle a large amount of bad/unstable sectors, over time your drive should have handled the sole unstable sector and should be able to carry on without problem. That a drive hasn't been able to pass the SeaTools long test is more a concern, that is typically a sign of hard drive failure.

3. I haven't yet looked at HD Disk Sentinel.

4. What kind of repair options?

5. So long as no data corruption or file system corruption is present, your images should be fine.

6. If it is indeed a drive problem, anything can be involved
My System SpecsSystem Spec
.

5 Days Ago   #14
Clairvaux

Windows 7 Home Premium 64-bit (OEM)
 
 

HD Sentinel has a class of test/repair commands which it calls Surface Tests, and which are supposed to be the more thorough/powerful among those it offers.

There are no less than 6 different variants of Surface Tests. I have uploaded the screenshots of their dialog boxes, which carry some explanations.

HD Sentinel's website has a lot of intriguing and challenging information about hard disk technology and maintenance. Unfortunately, it's a bit intimidating and confusing. It looks like it's a one-man outfit, and he could do with some help to clarify his ideas. Some interesting links :

Surface Tests
SMART issues
Why HD Sentinel is different
What's a "weak" or "bad" sector


Attached Thumbnails
Recurrent BSODs while imaging with Macrium, or just using new printer-read-test-non-destructive-16-juil-18.png   Recurrent BSODs while imaging with Macrium, or just using new printer-write-test-destructive-16-juil-18.png   Recurrent BSODs while imaging with Macrium, or just using new printer-write-read-test-destructive-16-juil-18.png   Recurrent BSODs while imaging with Macrium, or just using new printer-read-write-read-test-non-destructive-most-cases-16-juil-18.png   Recurrent BSODs while imaging with Macrium, or just using new printer-reinitialise-disk-surface-destructive-16-juil-18.png  

Recurrent BSODs while imaging with Macrium, or just using new printer-disk-repair-non-destructive-most-cases-16-juil-18.png  
My System SpecsSystem Spec
4 Days Ago   #15
axe0

Windows 10 Pro
 
 

Disk repair would be the option you want, but I don't see how it differs from a chkdsk /r command. Chkdsk /r does the exact same thing and much more....
My System SpecsSystem Spec
3 Days Ago   #16
Clairvaux

Windows 7 Home Premium 64-bit (OEM)
 
 

And CHKDSK /r we did try. Time to buy a new disk, I'm afraid, and maybe make it an SSD for system. Then swap the former system spinner into data use. Thank you.
My System SpecsSystem Spec
Reply

 Recurrent BSODs while imaging with Macrium, or just using new printer




Thread Tools




Similar help and support threads
Thread Forum
Imaging with free Macrium
This tutorial shows imaging with free Macrium Version 5.0. If you are still using Macrium Version 4.2, go to this Vimeo site where the tutorial of that version is stored. The Video does not show the recovery part because I have no setup to screen capture it. But Keith (Kado) made this excellent...
Tutorials
Recurrent BSODs with different error names
I keep getting these BSODs when I'm using my Samsung Series 7 Gamer laptop , when it's idle, when I'm shutting down, hibernating, etc. Sometimes it says IRQL_NOT_LESS_OR_EQUAL, then SYSTEM_SERVICE_EXCEPTION, then sometimes nothing at all. I reinstalled Windows. It was fine till I installed...
BSOD Help and Support
Issues imaging windows 7 pro with Macrium Reflect
Hello today i went an image my os windows 7 pro i follow that video on this forums .Than i went to restore tha image to another hdd in a partition .But when i booted from tha partition i got to the part were it said windows is preparing your desktop than i got a message saying that this copy...
Backup and Restore
Macrium Reflect - Cloning and Imaging?
Hi all, couple of days ago I had some difficulties with my SR not working which caused me a huge time waste of re-installation of windows. then I came here and you guys suggested me to use macrium and now I'm very happy with it. at this very moment I should be thankful to WHS, ignatzatsonic,...
Backup and Restore
Macrium Imaging Problem
Hi, I've encountered an issue using Macrium Reflect FREE x64 Version 4.2 Build 2952, and wonder if anyone can help me understand what is going on. I have used the very same version to image my C: and E: succesfully on a few occasions, using the existing XML defintion files. Now, however,...
Backup and Restore


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 04:18.
Twitter Facebook Google+ Seven Forums iOS App Seven Forums Android App