My stupid error -.- Blue Screen after change MSConfig 0xc000000e

SIW2 said:

Are you booting the media in bios mode?

Ther are some things you could try:

1. It is not necessary to have a separate system partition. You could mark the windows partition active and create the boot critical files on the windows partition.

2. If you use win8/10/11 bcdboot you can specify the mode with /f switch

e.g. bcdboot e:\windows /s c: /f bios

or after marking e: active

bcdboot e:\windows /s e: /f bios

Attachment 423267

I believe Bios Legacy because I've had this Windows installed for a long time and my stuff is old.
I was looking at setupact.log but I didn't find anything searching for "detected boot environment" inside the setupact.log
files I looked at them all.
My Bios is enabled to support "UEFI and Legacy"Windows 7 Ultimate 64-bit SP1
Intel Core i7 3770 @ 3.40GHz
32.0GB Dual-Channel DDR3 @ 798MHz (11-11-11-28)
Gigabyte Technology Co. Ltd. B75M-D3H (Intel Core i7-3770 CPU @ 3.40GHz)
2047MB NVIDIA GeForce GTX 760 (Gigabyte)
447GB KINGSTON SA400S37480G ATA Device (SATA-2 (SSD))
My windows is "Windows 7 Ultimate x64" (Partition in MBR).
Now I was reading a little about Bios legacy and UEFI... and I realized that the pendrive I have with Windows 7 that I'm using to create/arrange the bot is GPT..., from what I've been reading, the pendrive would have to be in MBR, is that it? ..
So I have to download a new image and save it to a pendrive in MBR...?
I downloaded the file you posted but I need it for win7..

thanks

SIW2 said:

You need to boot from the pendrive in bios mode (not efi) if you want to use win7 bcdboot.exe for an mbr system.

Newer versions of bcdboot have the /f switch which can be used when booted in the the wrong mode.

******************************

I have a b75m d3h,

booting nvme disk via pcie adapter on older machines

Ooooooooownnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn
finally after several hours trying to resolve it .

I formatted the pendrive where the iso was
I downloaded a new original iso only with Windows 7 Ultimate x64
I created the Bios MBR image on the pendrive using rufus
I formatted the 100mb partition (again, I think I formatted this partition about 50 times hehe)
I turned on the computer to boot from the pendrive, right at the beginning I noticed changes in the layout..
So I tested bootrec /rebuildbcd (but it didn't even find a system, strange because it used to find it... )
Then I used bcdboot e:\windows /s c: "command completed successfully." (e=where windows is installed,c=100mb partition where the boot is)
Then I also ran the restart fix tool twice. (I don't know if it helped but as it was there I took the opportunity to run it)
And then I restarted and it worked! I wasn't believing it.

If I had known about this issue with the GPT EFI boot and bios legacy mbr I wouldn't have wasted so many days trying to install an efi boot -.-
People talk a lot about GPT MBR etc but forget to say that the ISO needs to be written to one of these two to rebuild the boot!
I thought that when recording the ISO, both were recorded and the system would automatically include the correct one in the boot reconstruction, in the end I learned a lesson.
I'm not one to install Windows all the time, in fact I've been using mine for over 10 years without formatting, whenever I need to change HD/SDD I clone it and any problem that arises over the years I've always fixed it.
Note: While my main one was having a problem, I was using another SSD that has Windows 7 x64 ultimate installed in GPT with EFI boot, this helped to confuse me, I knew about recording the disk but I didn't know the boot issue.

Thank you very much for your interactions and help in the topic helped to resolve.