Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.

Windows 7: Help with Memtest-86 v4.10 & memory problem

04 Jun 2010   #11

Windows 7 Pro 64bit SP1

Quote   Quote: Originally Posted by usasma View Post
Two more qestions:

1) Memtest-86 v4.10 reports the following about the memory on all test runs: Settings: Ram: 533 Mhz (DDR1067) / cas : 8-5-5-18 / DDR2 (64bits)
OCZ support had me set cas as 5-5-5-18 ? These settings were confirmed in Windows via Speccy and Cpu-z. Is this an issue ?

Set Processor - NB Voltage to {1.35 volts} [ +150 mv]
Set Memory Clock Mode to {Manual}
Set DRAM Timing Mode to {DCT0}
Set Memory OverVoltage to {2.1 - 2.2 volts}
Set Memory Timings to 5-5-5-18 (TCL-TRCD-TRP-TRAS)
Set Memory Hole Remapping to {Enabled]
Set DCT Unganged Mode to {Always}
Sorry...I know I typed this but must must have edited out by accident before posting. The specs/bios settings were supplied by OCZ support..specifically on the timing ( cas ? ) as follows:

Set Memory Timings to 5-5-5-18 (TCL-TRCD-TRP-TRAS) per OCZ support
Memtest reports the following on all tests: cas : 8-5-5-18

The TLC setting is different here. Is this an issue ?


My System SpecsSystem Spec
04 Jun 2010   #12
Microsoft MVP


I don't know all that much about memory - but I'd expect that if it's correct in your BIOS, then it's MemTest that's reading it wrong.

Take Windows out of the equation here - check in the BIOS to see what the settings actually are. If they're wrong in the BIOS, change them to the OCZ setting. If they're right in the BIOS, then Windows and Memtest is probably wrong.

Try the Windows memory test and the - Memory Diagnostic to double check things. V3.5 of the doesn't work with 4+ gB of RAM - use the version 3.4a instead (if you have 4 or more gB of RAM.
My System SpecsSystem Spec
05 Jun 2010   #13

Windows 7 Pro 64bit SP1

Thanks for all your help...RMA in the works from OCZ...learned alot from you posts...

Thanks again
My System SpecsSystem Spec


 Help with Memtest-86 v4.10 & memory problem

Thread Tools

Similar help and support threads
Thread Forum
MEMORY MANAGEMENT BSOD - No memtest errors! - Help please!
Hi, I have today had a bsod which said memory management, i have the mini dump files if required. I dont understand why this is happening because i have checked my ram for 12 hours on memtest86 and it has come up with no errors, i have had no problems with my hardware before and since the...
BSOD Help and Support
Memtest and missing (PCI) memory addresses
If I place a single 4GB stick in my machine and run memtest, I see it's testing only 3.7GB. I assume this is the PCI memory map taking 0.3GB. Does this mean I'm not actually testing all the memory or am I missing something?
Hardware & Devices
BSOD after installing new memory, but memtest comes back all passed?
Hello, I've just recently purchased more memory for my computer and everything seemed to be working fine. Recently I've been getting 3B BSOD errors and just 5 minutes ago got one that was a 1E message. I've been trying to figure out why it was doing this, but when I look up the 3B message it says...
BSOD Help and Support
Can I test all memory at once with Memtest?
Hi all, I am trying to diagnose a problem with my machine, and in so doing I have run memtest overnight (to test all 8GB of RAM--which takes about 12 hours). However, I've read various places that memtest is only reliable testing one stick at a time (I have 4x2GB). I didn't get any errors in 7...
Performance & Maintenance

Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 17:19.
Twitter Facebook Google+