Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: BSOD Help

09 Jun 2010   #31
Jonathan_King

Windows 7 Professional x64
 
 

The only way you can damage your system is by increasing the voltage too much. Other than that, messing with clock speeds can only make the problem worse, or fix it.


My System SpecsSystem Spec
.
10 Jun 2010   #32
jsparry

Windows 7 64bit
 
 

Well i tried.

I managed to up the voltage and timings to what was stated on the ram.

And it lasted all night without any issues however after a restart this morning it went back to its usual trick and bsod me.

Message seemed the same as before.

I also noticed that when i turn the power on all the fans and lights turn on for a second then all go off then come back on again. just as it tries to post.

I think i'll try a format tonight when i get home from work (10am here) and see how that goes.
My System SpecsSystem Spec
10 Jun 2010   #33
Fumz

7 Ultimate x64
 
 

A good rule of thumb: whenever you're going to adjust voltage and timings in the bios, first set the correct voltage, save your changes and reboot back into the bios. Then set the correct timings, again saving your changes and rebooting into the bios, this time to make sure your changes have been applied correctly.
My System SpecsSystem Spec
.

10 Jun 2010   #34
jsparry

Windows 7 64bit
 
 

Any chance someone can take a look at these latest memory dumps.

Been trying everything i can think of....

I'm starting to think its hardware and trying to workout what device.

Thanks James
My System SpecsSystem Spec
11 Jun 2010   #35
Jonathan_King

Windows 7 Professional x64
 
 

Still looks like hardware.
Code:

BugCheck 1E, {0, 0, 0, 0}
Probably caused by : USBPORT.SYS ( USBPORT!USBPORT_Core_AllocIoRequest+30 )
ииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииии
BugCheck 1E, {0, 0, 0, 0}
Probably caused by : ntkrnlmp.exe ( nt!KiKernelCalloutExceptionHandler+e )
ииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииии
BugCheck 6B, {0, 0, 0, 0}
Probably caused by : ntkrnlmp.exe ( nt!Phase1InitializationDiscard+1331 )
ииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииии
BugCheck 1E, {ffffffffc0000005, fffff80002d89f35, 0, ffffffffffffffff}
Probably caused by : ntkrnlmp.exe ( nt!ObpWaitForMultipleObjects+2ff )
ииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииииии
You can try updating your USB port drivers, but I suspect RAM.
My System SpecsSystem Spec
11 Jun 2010   #36
jsparry

Windows 7 64bit
 
 

Well, I've rulled out Gfx card (have a spare).

Just downloaded a HHD checker.


I've run the memory tester again and its passed all 4 times. If memory is to blame could it still pass?
My System SpecsSystem Spec
12 Jun 2010   #37
jsparry

Windows 7 64bit
 
 

Is there any way to check if its the mobo, or psu.
My System SpecsSystem Spec
12 Jun 2010   #38
jsparry

Windows 7 64bit
 
 

I've tested the ram one stick at a time with Memtest86+.

1st stick passed 5 times.

2nd stick is on 2nd pass atm
My System SpecsSystem Spec
12 Jun 2010   #39
Jonathan_King

Windows 7 Professional x64
 
 

I must have been foggy the first time I responded?

Why did I not ask you to enable driver verifier?
My System SpecsSystem Spec
12 Jun 2010   #40
jsparry

Windows 7 64bit
 
 

Ahh ok ill put it back on now then.

I've only got 1 stick on ram in atm and i'm doing a stress test to watch mobo voltages to run out psu or mobo.
My System SpecsSystem Spec
Reply

 BSOD Help




Thread Tools



Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

й Designer Media Ltd

All times are GMT -5. The time now is 17:15.
Twitter Facebook Google+ Seven Forums iOS App Seven Forums Android App