Any Vapers?


  1. Posts : 4,517
    Windows 7 Home Premium 64bit
    Thread Starter
       #1311

    I just got a new tank section for my Kayfun. The original held 4.5ml but had a small see through section between 2 stainless steel pieces.

    The new one holds 3.5ml, and is much shorter. Gone are the stainless steel section on top and bottom replaced with a single See through section.
    Any Vapers?-1.jpg

    I do like it better this way, because its shorter, and I think it looks better overall.
    I go through 5-6ML of Juice a day, so a daily refill is always needed with either set up.



    I've been thinking about getting a DNA40 mod of some sort though. Maybe try out that new Kanger Tank,.
      My Computer


  2. Posts : 5,915
    Windows 10 Pro X64
       #1312

    Looking good Wishmaster
      My Computer


  3. Posts : 6,075
    Windows 7 Professional 64 bit
       #1313

    Looks really nice Wishmaster. I think you will like the Sub tank. In my opinion the RBA part is a bit of a waste of time. It's very fiddly and with it fitted the draw is a bit tight for my liking. But the 0.5ohm OCC coil is excellent.

    I just re-wicked a 0.5ohm OCC coil, I managed to do it without taking it apart. If you are very careful with the use of something like a dart (which is what I used) you can gently feed the old cotton out through the side hole. Once that's done it's just a case of putting the new cotton through one side hole, through the coil and straight out the other side hole. Cut it off each side with around 4mm hanging out, fluff it up and job done.
    The original cotton lasted for 3 weeks before it lost flavor.

    I also got some replacement O rings from the vendor I bought the sub tank from and I have just fitted them and thankfully I can confirm it has cured the leaking issue.
      My Computer


  4. Posts : 5,915
    Windows 10 Pro X64
       #1314

    I grabbed a bad dry hit last night. Was chain vaping, surfing the web. Didn't pay attention that the tank was out of juice. Reading along, picked up my mod and took a long hard hit. Coughing my lungs up, I looked at the mod. Ohms read 6.2 and I saw I was out of juice.

    After finishing my coughing fit, I refilled the tank. All is good again. That was one nasty hit. If you ever watched Pulp Fiction, this pic will pretty much give you a visual of how it tasted

    Any Vapers?-dry-hit.png
      My Computer


  5. Posts : 4,517
    Windows 7 Home Premium 64bit
    Thread Starter
       #1315

    Haha. good way to illustrate the point.

    Nothing tastes worse than a burnt wick!
      My Computer


  6. Posts : 6,075
    Windows 7 Professional 64 bit
       #1316

    Lol, a dry hit sorts the men from the boys eh Doug!
      My Computer


  7. Posts : 5,915
    Windows 10 Pro X64
       #1317

    paulpicks21 said:
    Lol, a dry hit sorts the men from the boys eh Doug!
    Sure does. I had to go brush my teeth, drink some water, and still waited a while before I hit the mod again
      My Computer


  8. Posts : 5,915
    Windows 10 Pro X64
       #1318

    paulpicks21 said:
    Dude said:
    paulpicks21 said:
    Cheers for the vid Doug. The Mini looks like a winner. It's in stock in the UK now. If I didn't already had 2 good tanks I might have got it.
    Yeah, I'm still wanting the melo....but

    I say you go for that new Sub Tank Mini Doug

    New badge alert for me but size isn't everything as they say
    Well Paul I haven't got a new tank yet, but you can see here I do have a 6ml tank running Not that I'm a badge chaser or anything or am I?

    Today has been good, no dry hits!

    Any Vapers?-2015-01-26-13-27-25.348.jpg
      My Computer


  9. Posts : 6,075
    Windows 7 Professional 64 bit
       #1319

    Lol, you just filled her up a bit higher eh! No harm in that.
      My Computer


  10. Posts : 5,915
    Windows 10 Pro X64
       #1320

    Yep, dry hits scare me!
      My Computer


 

Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 06:08.
Find Us