Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Renesas Electronics USB 3.0 Host Controller Not working

16 Oct 2013   #1
LoneZ

Windows 7 Home Premium 64bit
 
 
Renesas Electronics USB 3.0 Host Controller Not working

So I accidentally uninstalled the program and my driver stopped working. I went over to hp website to find the software and driver and installed but it does not work.




Attached Thumbnails
Renesas Electronics USB 3.0 Host Controller Not working-yes.png  
My System SpecsSystem Spec
.
16 Oct 2013   #2
Boozad

W7 Pro x64 SP1 | W10 Pro IP x64 | W8.1 Pro x64 VM | Linux Mint VM
 
 

If this was recent do you have a Restore Point dated before you uninstalled the program?
My System SpecsSystem Spec
16 Oct 2013   #3
LoneZ

Windows 7 Home Premium 64bit
 
 

I just realised that I don't even have a restore point... :/
My System SpecsSystem Spec
.

16 Oct 2013   #4
Boozad

W7 Pro x64 SP1 | W10 Pro IP x64 | W8.1 Pro x64 VM | Linux Mint VM
 
 

What is the model number of your PC?
My System SpecsSystem Spec
16 Oct 2013   #5
LoneZ

Windows 7 Home Premium 64bit
 
 

Its a HP Pavilion Slimline s5-1351d
My System SpecsSystem Spec
16 Oct 2013   #6
Boozad

W7 Pro x64 SP1 | W10 Pro IP x64 | W8.1 Pro x64 VM | Linux Mint VM
 
 

Have you used the 'scan now' option on this page? Hopefully that should identify what you need.
My System SpecsSystem Spec
16 Oct 2013   #7
LoneZ

Windows 7 Home Premium 64bit
 
 

Doesn't even work for me. It can't detect anything.
My System SpecsSystem Spec
16 Oct 2013   #8
Boozad

W7 Pro x64 SP1 | W10 Pro IP x64 | W8.1 Pro x64 VM | Linux Mint VM
 
 

Are you sure your host controller is a Renesas? The only USB drivers I can find on that page is for a Texas Instruments XHCI controller.
My System SpecsSystem Spec
17 Oct 2013   #9
LoneZ

Windows 7 Home Premium 64bit
 
 

Most likely yes. The USB ports stop working when I uninstalled that program.
My System SpecsSystem Spec
17 Oct 2013   #10
Boozad

W7 Pro x64 SP1 | W10 Pro IP x64 | W8.1 Pro x64 VM | Linux Mint VM
 
 

Right, did the Renesas program come preinstalled on your system? And what driver did you try from the HP website?

Can you download and run Piriform Speccy and post a screenshot of the system information it gives you, we need to find out what hardware you have to determine which drivers you need.
My System SpecsSystem Spec
Reply

 Renesas Electronics USB 3.0 Host Controller Not working




Thread Tools




Similar help and support threads
Thread Forum
Renesas Electronics USB 3.0 Host controller failed on Dell laptop
I had tried to download it from the manufacturer (Dell) But it keeps failing. I get an error stating that it cannot start (code 10). I have 1 USB port on the left and 3 USB ports on the right. Only 1 works on the right, the one on the left still works. It started after I had shut it down for...
Drivers
USB 3.0 Host Controller Not Found
I know this is a well documented situation and I have seen and read a lot of information about the problems others have had with the USB 3.0 Host controller. My situation is that I have followed several different solutions only to wind up with USB's on the 3.0 hub not working after reboot. I have...
Drivers
USB 3.0 Host Controller Not Found
I've just recently upgraded my pc but i'm having issues trying to install and setup the drivers for the usb3.0 ports and updating the firmware. I'm running on Windows 7 x64 My motherboard is the P8P67 PRO Rev. 3.0 - New P67 B3 Revision I have tried the drivers and firmware from here without...
Drivers
USB - Enhanced USB Host Controller Not working - Drivers!!!
Folks, I have been working on this on/off all weekend and I STILL cannot get my USB 2.0 ports to work again and they were all working fine for the past 10 months. All 8 USB ports stopped working in 2.0 mode last week. They work perfectly fine in 1.1 mode using the standard Host Controller (BIOS...
Drivers
Fresco Logic USB 3.0 Host Controller - Not working after pc restart
Hi, Recently got Fresco Logic USB 3.0 Host Controller (PCI Express Card), first tried and it was cool with ~60-80MB/s transfer rate. However, soon after I restarted the computer, the PCI card no longer works - cannot detect any usb device connected :cry:. Having said that, device manager does...
Hardware & Devices


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 05:01.
Twitter Facebook Google+