Drivers for Marvel 91xx Config ATA Device...  

Page 1 of 3 123 LastLast

  1. Posts : 24
    Windows 7 Ultimate x64
       #1

    Drivers for Marvel 91xx Config ATA Device...


    Hello!

    I need help installing the following drivers:

    Drivers for Marvel 91xx Config ATA Device
    Jmicron JMB36X Driver
    marvel 91xx driver
    Marvel Storage Utility V4

    I recently formatted my computer and had these installed, the SATA drivers from my motherboards website do not work. I get the error "this computer does not meet the minimum requirements for installing the software sata".

    Thanks :)
      My Computer


  2. Posts : 21,007
    Desk1 7 Home Prem / Desk2 10 Pro / Main lap Asus ROG 10 Pro 2 laptop Toshiba 7 Pro Asus P2520 7 & 10
       #2

    Hello Anima mate I think are what you are after Marvell - Support - Driver Downloads the only thing I don't know is if the part number has to included.
    More are Gigabyte Marvell Storage Utility 4.1.0.1921 Driver - TechSpot

    JMicron JMB36X SATA Controller Driver 1.17.65 Driver - TechSpot

    To find the part number you may need to run HE Info and get the deetails of that part number - if it will bring it up.
    See my ditty

    Using HW Info

    You can test the volts on the PSU with HWInfo HWiNFO, HWiNFO32/64 -Download < download the right bit version andclose the right hand window select Sensors and scroll down to the power sectionwhere you will see what the volts are doing see my pic.

    The original right hand window shows themachine running and is handy for that but for looking at the components in some detail close it and use themain left hand side panel

    FOR OTHER COMPONENTS

    Open each + down into the componentitself and then click on it - in theright hand side will appear all sorts of details including brands speeds andother essential info that device. See pic for example.
    (I have included one for my GPU so you can see how it opens out in minute detail)
      My Computer


  3. Posts : 24
    Windows 7 Ultimate x64
    Thread Starter
       #3

    Details


    Hey mate!

    Thanks for your reply and help so far, much appreciated, i got the other drivers out the way but the "marvell 91xx config" has still been a doozey to find. I've posted a picture of the details of it from that software you recommended in case it might help, I've scoured the internet and couldn't find anything.

    Also on a similar note, how does one check whether all his drivers are updated? (in case I've missed something).

    Thanks! :)
      My Computer


  4. Posts : 24
    Windows 7 Ultimate x64
    Thread Starter
       #4

    Opps, forgot image!


    Image
      My Computer


  5. Posts : 21,007
    Desk1 7 Home Prem / Desk2 10 Pro / Main lap Asus ROG 10 Pro 2 laptop Toshiba 7 Pro Asus P2520 7 & 10
       #5

    Slowly tracking this one down I think as this Google shows it points to something to do with a) that flaming part number and / or b) the board itself.
    Download for the "Marvell 91xx Config ATA Device" - Microsoft Community

    The Marvell site again is this Marvell - Support - Driver Downloads

    Am going to dig around in the board site now but at least it looks like it has been a problem in the past.
      My Computer


  6. Posts : 21,007
    Desk1 7 Home Prem / Desk2 10 Pro / Main lap Asus ROG 10 Pro 2 laptop Toshiba 7 Pro Asus P2520 7 & 10
       #6

    Have foiund this but am not sure it is what we are looking for - fingers crossed
    Motherboards - RAMPAGE III FORMULA - ASUS > open the SATA drivers up.
      My Computer


  7. Posts : 24
    Windows 7 Ultimate x64
    Thread Starter
       #7

    Sata Error


    I tried installing the Sata drivers from the asus website but i get the error message "this computer does not meet the minimum requirements for installing the software sata".

    I read somewhere that it might be because i installed windows on a certain setting from BIOS or something, not sure, something along those lines, ring any bells?
      My Computer


  8. Posts : 21,007
    Desk1 7 Home Prem / Desk2 10 Pro / Main lap Asus ROG 10 Pro 2 laptop Toshiba 7 Pro Asus P2520 7 & 10
       #8

    Dean mate what form of BIOS do you have on that board cos I have an idea that it is the older type as opposed to EUFI.

    Now I have attached two pics of the different kinds of BIOS to show you what I mean by the older type. Boot and go into the BIOS let us know which it is please the blue screen one will be the older type the EUFI has a black screen and dials on and lot more on it .

    Now again I have an idea that it is the older type and it needs to be set to ACHI and you need to set it to that. See this
    https://www.sevenforums.com/tutorials/61869-ahci-enable-windows-7-vista.html
      My Computer


  9. Posts : 24
    Windows 7 Ultimate x64
    Thread Starter
       #9

    It's definitely the older "blue screen" one however I don't understand why it would be any different.

    When I formatted my computer the only thing in BIOS I changed was the "Hard Disk Drives" order and "Boot Device Priority" so that I could install Windows via U.S.B. Would that have any significant influence on the driver not being able to be installed?

    Thanks :)
      My Computer


  10. Posts : 21,007
    Desk1 7 Home Prem / Desk2 10 Pro / Main lap Asus ROG 10 Pro 2 laptop Toshiba 7 Pro Asus P2520 7 & 10
       #10

    Dean read the tutorial - having ACHI set is an advantage and it maybe why the system is refusing to do what you want.

    Have a read of this before you make any decisions though. AHCI vs IDE - Difference and Comparison | Diffen

    Myself I am ACHI all the way
      My Computer


 
Page 1 of 3 123 LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd
All times are GMT -5. The time now is 11:28.
Find Us