Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: SSD Install, Drivers needed?

30 Jul 2018   #1
ariespaan

Windows-7 64 Bits Home Premium
 
 
SSD Install, Drivers needed?

HI,
I am working with a Laptop and Win-7 using a 500 Gb Internal HD
I now want to install a 500 Gb SSD Unit (Samsung EVO 640)

I first clone mine 500 GB HD to the 500 GB SSD with Macrium Reflect free
Than i change the old HD with the new SSD.
My question is: Do i also need to install a driver for the new SSD i installed
And if so, where can i find a driver for the SSD or does it works fine without a new driver for gthe SSD?
Thanks


My System SpecsSystem Spec
.
30 Jul 2018   #2
mrjimphelps

Linux Mint 18.2 xfce 64-bit (VMWare host) / Windows 8.1 Pro 32-bit (VMWare guest)
 
 

You don't need any drivers for an SSD. If your hard drive works in that computer, then the SSD will work.

Did you do a "clone" (sector-by-sector) backup or an "image" backup? I strongly suggest that you do an image backup of the hard drive, then an image restore to the SSD, if that's not what you have already done. The problem is, an SSD is not the same as a mechanical hard drive, so the clone won't match the SSD like it would another mechanical hard drive.

Make sure TRIM is active on the SSD.

I have heard that you need to "align" the SSD, but I don't know anything about aligning an SSD, so I can't comment on that.
My System SpecsSystem Spec
30 Jul 2018   #3
ariespaan

Windows-7 64 Bits Home Premium
 
 

I have not yet done the cloning at this moment.
In the past i had done a cloning of an old 500 GB HD to a new 500 GB HD, and i used Macrium Reflect free for that purpose
(I dont know what type of cloning Macrium reflect did at that time, and i intended to do the same procedure to clone my HD to a SSD-Drive now.

I see what you mean with your reply and when a do the cloning now i do that with the procedure you recommended.
Thanks for your advice.
By the way: I read some articles about trimming the SSD later on, and i will loom it up again when i needed it.
My System SpecsSystem Spec
.

30 Jul 2018   #4
F22 Simpilot

Windows 7 Ultimate x64
 
 

To make sure the TRIM command is on: Check and Enable or Disable SSD TRIM Support in Windows 7 / Windows 8.1 -MWH

You did have AHCI enabled in your BIOS?

To check alignment use CrystalDiskInfo. CrystalDiskInfo Crystal Dew World

To align a SSD: How to Align SSD After Clone - EaseUS
My System SpecsSystem Spec
30 Jul 2018   #5
ailsa

Windows 7 Ultimate x64
 
 

A driver is a bridge between software and hardware. But most common hardware, driven by widnows, doesn't require a separate installation. Such as the keyboard and mouse, as well as the hard drive.
Solid-state drives are usually installed automatically by the system. Once the AHCI option in the BIOS is turned on, the AHCI driver is automatically installed when the system is installed. If you install the system in IDE mode, you need to install the driver separately after the system is installed.
hope it's helpful.
My System SpecsSystem Spec
02 Aug 2018   #6
AddRAM

Windows 7 Pro x64 Windows 10 Pro x64
 
 

Windows will install any drivers for it after you have it up and running, just check in Device Manager for any issues.

I did not know Samsung made a 640 SSD.

Could you post a link


Attached Thumbnails
SSD Install, Drivers needed?-dm.jpg  
My System SpecsSystem Spec
Reply

 SSD Install, Drivers needed?




Thread Tools




Similar help and support threads
Thread Forum
2 drivers needed - can you help?
Hi Everyone have just done a fresh install of Windows 7 pro 64 bit on my HP ProBook 6550b laptop. All is well, with the exception that device manager shows two entries that relate to missing 'base system device' (No drivers installed.) Try as I might, I cannot trace the correct drivers anywhere....
Drivers
A second install of windows 7 - but lots of drivers needed!
Hi All, I've run out of space on an old small SSD, and have decided a clean start is probably the best way to go in setting up Windows 7 64 bit on my shiny new bigger SSD. I plugged in the new drive, successfully installed Windows 7, and can boot to it. Great start! Thing is though, it's...
Installation & Setup
Drivers Needed
acer synaptics toutch pad driver 15.3.41.5 acer intel vga driver 6.14.00.3090 where to find these for free
Drivers
Windows install : device drivers needed
I'm having some issue with my computer, and to solve that I'm trying to install Windows 7 again. I've yet NOT managed to do that ever on this computer, which is about 1 year old. There's no multiboot or whatever, BUT, there is a RAID controller active, and RAID is actually enabled. Actually, now...
Installation & Setup
Drivers Needed for Install
After an entire day of trying to fix my laptop and get it to Reset to Factory Image I have found that the Setup.exe file to install Win7 is on my hard drive (X:Boot). Only problem is I get this error when I try to install it. A required CD/DVD drive device driver is missing. If you have a...
Installation & Setup


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 16:13.
Twitter Facebook Google+