Toshiba SatelliteL455-S5976 Blk screen on boot with mouse cursor help

Page 4 of 7 FirstFirst ... 23456 ... LastLast

  1. Posts : 36
    7
    Thread Starter
       #31

    I got through copying windows files, expanding windows files, installing features, and now its been stuck for about 20 mins on installing updates, no cpu or dvd lights are blinking. Now what?
      My Computer

  2.    #32

    Wait. If it fails try entering Device Manager to disable any drivers which are erroring with a ! to see if install will complete. Device Manager - Access During Windows 7 Installation

    What were the results of the HD Diagnostic bootable CD scan I linked you earlier?
      My Computer


  3. Posts : 36
    7
    Thread Starter
       #33

    gregrocker said:
    Wait. If it fails try entering Device Manager to disable any drivers which are erroring with a ! to see if install will complete. Device Manager - Access During Windows 7 Installation

    What were the results of the HD Diagnostic bootable CD scan I linked you earlier?
    Failed to make swap----= failed to unmount hard disk !!

    that was it oh and a eth0 failure assumes DHCP is setup.

    those are the only 2, the 2nd i think is because i run wifi, not hard wired.
      My Computer

  4.    #34

    Are you referring to an attempt to run bootable HD diagnostics? Which one did you run? Try it again if install fails. Try also running Disk Check from the installer Command line.
      My Computer


  5. Posts : 36
    7
    Thread Starter
       #35

    Just got a windows error! Error code: 0xE0000100 Verify that the installation sources are accessible, and restart installation.
      My Computer


  6. Posts : 36
    7
    Thread Starter
       #36

    then rebooted itself and says system registry file is missing or corrupt.


    Trying to load windows in safe mode with networking. says please wait...
      My Computer

  7.    #37

    The problem is even more likely now the hard drive. Run the HD DIagnostics and Disk Check as specified.

    What is the HD brand? If you don't know you can download and burn to CD Seagate Seatools to boot and run Extended Scan.
      My Computer


  8. Posts : 36
    7
    Thread Starter
       #38

    I just got chkdsk up and running and just clicked F as the switch to fix errors on the drive right away. Do I do this just once or reboot up to like 3 times? I will download and imag burn the seagate now meanwhile.

    Not sure on HD type. sorry. adding errors as they pop up.


    can't run sea scanner because as of now I can't get into 7 yet, but there was 1 error so for...

    correcting error in index $130 for file 1720. and under it the same one again. Does that help? Says its fixed now. Still running.

    now. correcting error in index $130 for file 2800. under it says same thing again
    Last edited by BadCompany; 25 Nov 2012 at 19:36. Reason: added info
      My Computer

  9.    #39

    Seatools will tell you the HD brand, or give a model number to google to find out. It may find problems to fix. If not Disk Check may be enough, or the HD may need it's maker's diagnostics to diagnose or do repairs.
      My Computer


  10. Posts : 36
    7
    Thread Starter
       #40

    Alright thanks, so can the installation just resume from where it left off or do i have to go back in and whipe it all out again and start over 100%?
      My Computer


 
Page 4 of 7 FirstFirst ... 23456 ... LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 07:21.
Find Us