Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.

Windows 7: Computer won't turn off

03 Jan 2013   #1

Windows 7 Professional x64
Computer won't turn off


I recently re-installed windows 7 on my computer, and after i installed all of the drivers, i realized my computer wouldn't shut down.

I mean, it says its shutting down, then the screen goes into standby mode, but the computer keeps running.
I don't understand why or how this could happen.

It's weird, i even tried rolling back on some bios changes i made, but nothing. I don't even know how to troubleshoot this. I tried googling it, but everyone that has a different problem on which the shutting down screen persists.

Any help would be appreciated.


My System SpecsSystem Spec
03 Jan 2013   #2

Win7 Ultimate X64

My System SpecsSystem Spec
03 Jan 2013   #3

Windows 7 Professional x64

I think i prematurely made this thread as i just fixed it by reverting an old bios setting that i thought wouldn't influence. It was set on AHCI, then i changed back to IDE and it worked. OR maybe it was just a coincidence and this just happens when there are updates involved. Will let you guys know if it happens again!

Another thing that's bothering me though, is how long it takes for the computer to go into shut down mode.
Before formatting, i remember clicking shutdown and it instantly went to that Shutting Down screen. Now it hangs for about 6-7 seconds, shows that force close screen with no programs in it, and then goes to the shutting down screen. I tried setting the wait timer to kill service to 2 seconds, but that didn't help.
Any ideas?
My System SpecsSystem Spec

03 Jan 2013   #4

64-bit Windows 10 Pro

Hello Alex,

If you have hibernate enabled, then that could take a few seconds at shutdown to save memory to the hard drive before shutting down.
How to Enable or Disable Hibernate in Windows 7 and Windows 8
In addition, double check to make sure that you don't have Windows set to clear the page file at shutdown. It's not by default.
How to Enable or Disable "Clear Virtual Memory Paging File at Shutdown" in Vista and Windows 7
Hope this helps, :)
My System SpecsSystem Spec
03 Jan 2013   #5

Win7 Ultimate X64

You can't change between IDE and ahci this should be done before installing windows it is possible to do now but it's a real pain
My System SpecsSystem Spec
03 Jan 2013   #6

Windows 7 Professional x64

Quote   Quote: Originally Posted by Pauly View Post
You can't change between IDE and ahci this should be done before installing windows it is possible to do now but it's a real pain
Oh so that's what was causing the shutdown issue?
There are two different settings in my bios on which i can choose AHCI or IDE or RAID.

One is in a marvell tree and the other one is a standalone one. I don't know why you would be able to choose two ways, but i'm guessing the one that affects the disk is the marvell one right?

By the way, i'll give it a try on that page file clear tutorial. Can't test the shutdown now as i have multiple downloads active.
My System SpecsSystem Spec
03 Jan 2013   #7

Win7 Ultimate X64

TBH im suprised it even booted
You have two places as you have 2 sata controllers on your mobo, one intel controlled by chipset and a seperate one controlled by marvell so depends which sata plugs on mobo you connected your HDD too, heres a snip of your mobo specs so actually with jmicron controller you may even have three
Computer won't turn off-capture.png

My System SpecsSystem Spec
03 Jan 2013   #8

Windows 7 Ultimate x64

try to make a new user and check it there too, you may accidentally changed your registry and this happened!
My System SpecsSystem Spec
03 Jan 2013   #9
Layback Bear

Windows 10 Pro. 64/ version 1709 Windows 7 Pro/64

Take a look here.
ASUS - Motherboards- ASUS Maximus IV Extreme-Z
> Under expansion slots. (Red and/or Gray)
Intel® Z68 chipset : *1
2 x SATA 6Gb/s port(s), red
4 x SATA 3Gb/s port(s), gray
Support Raid 0, 1, 5, 10
Support Intel® Smart Response Technology on 2nd generation Intel® Core™ processor family
Marvell® PCIe 9182 controller : *1
2 x SATA 6Gb/s port(s), red
All this information should be in your Motherboard Manual. As you can see Marvell controls the red sata ports and Intel controls the gray sata ports. I use nothing but Intel controlled ports because Marvell has been nothing but a head ache on my board.
My System SpecsSystem Spec

 Computer won't turn off

Thread Tools

Similar help and support threads
Thread Forum
How do I know the host computer turn on or turn off?
I am using a client computer that is connected to a modem via a LAN cable which is in a neighboring house as far as about 50 meters. The host computer is there. The host computer is only using Internet Connection Sharing (without a router) to share its Internet connection with me. Within this...
Network & Sharing
Need Help! My computer can't normally turn down!
Hello there. My computer can not normally turn down. I have to push the power button to turn it off. When I use the mean>turn off. It will keep loading, I have been let it load for one day. Still loading. So everytime I have to push to turn it off. I tired to restore to early backup, But all backup...
BSOD Help and Support
BSOD after I turn Computer NEW Computer on, or whilst sleeping
New computer keeps blue screening during or after my computer goes to sleep. Was told to upload this, and also it says part of the reason is in the Minidump folder or the Temp folder.
BSOD Help and Support
Computer turn on and off itself? Help
Hellow guys, i'm also currently have an issues where, when i switch on the main switch, the computer turn on itself, i didnt even press the power button! And after a few second, maybe 2 to 3 or 4, it turn off itself again. When i press the power button myself, there is no more power. I cant turn it...
General Discussion
My Computer monitor doesn't show anything when I turn my computer on.
First of, my monitor exhibited signs of flickering during start-up, but only minor ones and would just stop at the 'Welcome' screen of windows so I didn't give it much thought. Iv'e been using it with the cpu the same time I bought the monitor. But after some time, the flickering got worse. It...
Graphic Cards

Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd

All times are GMT -5. The time now is 07:22.
Twitter Facebook Google+