computer wont load windows on boot up

Page 8 of 11 FirstFirst ... 678910 ... LastLast

  1. Posts : 26,869
    Windows 11 Pro
       #71

    rogerthedodger said:
    can i run memtest at the same time as prime ?
    Not possible. So, no. You run Prime from within Windows and memtest by booting into the test media.
      My Computer


  2. Posts : 1,965
    win 7 X64 Ultimate SP1
       #72

    Memory


    If I read your specs correctly you have two kinds of mem installed. I don't see either type in the recommended vendor list for that board.

    also the slots they are installed in are critical. from the manual:
    install identical DIMMs in all four sockets OR

    install identical DIMM pair in DIMM_A1 and DIMM_B1 (yellow sockets)
    and another identical DIMM pair in DIMM_A2 and DIMM_B2 (black
    sockets)
    Always use identical DDR2 DIMM pairs for dual channel mode. For
    optimum compatibility, it is recommended that you obtain memory modules
    from the same vendor. Visit the ASUS website (ASUS) for the
    latest Qualified Vendors list.

    Just an observation may not help.
      My Computer


  3. Posts : 60
    windows 7 64 bit home edition
    Thread Starter
       #73

    i got that tracer crucial ballistix which has the led lights but the third stick was faulty so i went to crucial website for recommendations and as the tracer was not available they sent me what they thought was compatible but when prime stops in 5 hours i,ll start memtest as i have that on disc
      My Computer


  4. Posts : 1,449
    Windows 7 ultimate 64-bit
       #74

    rogerthedodger said:
    My Bios has never been updated could this be the problem and i tried Speedy Pc Pro but that didnt solve the issue this damn pc is driving me nuts
    This could be quite possible. If there are any updates for it you should check into installing them carefully as sometimes the updates look like they are for your motherboard; when they really arent and if you install the wrong one etc. it can render the motherboard useless.
      My Computer


  5. Posts : 1,965
    win 7 X64 Ultimate SP1
       #75

    Manual and Bios


    Bios loading is explained in the manual in section 4.1. If your existing bios has Asus crash free bios it is my prferred method. I have used it several times. You will need to visit Asus and get the latest ver and put it where you know you can find it. Using OS as Vista 64bit the latest non beta ver I see is 1202.

    ASUS Service | North America

    The method I mention above removes the net from the equation thus is more reliable.

    Manual: Manual.zip
      My Computer

  6.    #76

    The BIOS was updated to 1202 yesterday.

    I would watch the temps. Heat could be a cause of your problem, is one of the checklist in Troubleshooting Steps for Windows 7.

    Did you do the CPU thermal pasting, so you know it is intact and sufficient? I'm assuming the case is not full of dust with all the change-outs you've done.

    I would install CoreTemp to monitor temps in the System tray, set alerts.
      My Computer


  7. Posts : 60
    windows 7 64 bit home edition
    Thread Starter
       #77

    Last week my brother in law took my pc and stripped it down cleaned it and tried to resolve the problem but he was unable to do so we reseated the processor with thermal paste and as i type this i am running prime95 and this time the temp hasnt risen above 25c so far i am going to have to run memtest tomorrow i will be back later to ask for more guidance as pc wont boot into installation dvd in normal mode for some reason but i will finisg prime95 first
      My Computer


  8. Posts : 26,869
    Windows 11 Pro
       #78

    Roger, what are you using for temp measurement? I have never seen a CPU run Prime and not go over 25C. Are you sure you are looking at the CPU temp?
      My Computer


  9. Posts : 60
    windows 7 64 bit home edition
    Thread Starter
       #79

    i have a x blade case and on the front near the top there is a cpu temp gauge and currently it is showing 20c my tower has 4 fans running i dont know if this is correct or not but i have been running prime since 17.20pm our time and all stress tests are showing a pass.

    Edit i have now stopped prime95 and starting memtest which does 2 passes at a time
      My Computer


  10. Posts : 60
    windows 7 64 bit home edition
    Thread Starter
       #80

    When I checked memtest it showed that I had 82 errors is this because I have them incorrectly fitted but I am now doing a diskpart format which is taking its time to complete
      My Computer


 
Page 8 of 11 FirstFirst ... 678910 ... LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 07:23.
Find Us