Booting/PC starting problem?

If you are turning off the power to your AX-860i what is happening is normal.

That on off process is the power supply doing a self test.
Every time you remove the power to the power supply and then turn the power to it back on and start your computer it is designed to do a self test.

Layback Bear said:

If you are turning off the power to your AX-860i what is happening is normal.

That on off process is the power supply doing a self test.
Every time you remove the power to the power supply and then turn the power to it back on and start your computer it is designed to do a self test.

see this

The Power good signal voltage at pin 8 on the 24 pin plug (grey cable) should be the same as the 5v rail reading/s
See this for the rail voltage info
PSUs 101: A Detailed Look Into Power Supplies (Section 2.)

[QUOTE=saresu;3268976]

saresu said:

Layback Bear said:

If you are turning off the power to your AX-860i what is happening is normal.

That on off process is the power supply doing a self test.
Every time you remove the power to the power supply and then turn the power to it back on and start your computer it is designed to do a self test.

I see... But why now?
I always turn the switch off at the PSU and use PC days later, I've been using like this over 2 years. It's never happened before

And what about the Internet icons?

Yes mate we hear what you are saying but like anything else a PSU can go bad even after a short time of operation and two years is a long time if the device is used at heavy loads. I don't understand why you switch it off at the PSU though I always switch my equipment with the Start button and then off at the uninterrupted power supply unit and surge boards so that the machines are in essence isolated from the mains supply - it could be over use of that switch causing issues because as you may know any switch causes a tiny arc each time it is actuated and tends to burn the contacts a tiny bit more each time.
As you said read through tht article I linked.

No I know what you are doing powering doin then switching the PSU off with it's rocker power switch. What I am saying is inside the switch there are contacts that are opened and closed each time you operate it and the mere touching of the switch contacts creates if only on a very small scale a small spark (arc) and it can gradually eat away at the contacts surfaces. You only have to switch off at where the power lead is plugged in at the mains input or the surge board switch - operating the PSU switch is really not necessary at all - you gain absolutely nothing by doing so. If you are doing it in case of a power surge, dropout or direct lightning strike then particularly with a a lightning strike just flicking the switch off will achieve nothing because of the enormous power that will connect to it via the mains power lead by the extremely high voltage "jumping" the gap .
You are best shutting the power off at your surge board and even that is no absolute protection against what I have described above - that can only be avoided by unplugging the entire power source from the wall.
The pic is simplistic and PSU switches usually have four contacts inside two for positive and two for negative - what they call a double throw switch.

No mate I am not saying that you have probably damaged the contacts or the PSU just that the least you use that method of shutting the PSU down the less likely to are to create more wear on the switch contacts.

Now we can get back to the problem if you get into safe mode run these
SFC /SCANNOW Command - System File Checker
Disk Check < if necessary include the /f and /r in the command line as per Option2
Run these in safe mode and the sfc often best run for two to three runs

Now it this gets system going properly again then all well and good if not run this for us so we can rule out the PSU rail voltages.
Using HW Info
PART A:
You can test the volts on the PSU with HW Info HWiNFO, HWiNFO32/64 - Download < download the right bit version and close the right hand window select Sensors and scroll down to the power section where you will see what the volts are doing see my pic. In my pic the section (Nuvoton) with VBATT as a dead give away you are in the section for the rail voltages. There are other section titles and one that pops up often is ITE (sometimes the usual one for Gigabyte boards)
Now the voltage on the different rails have to be within 5% =+/- of what is required or the machine will not work properly if at all.
Limits +/-
12v = 11.4 – 12.6v
5v = 4.74 – 5.25v
3.3v = 3.135 – 3.465v
The Power good signal voltage at pin 8 on the 24 pin plug (grey cable) should be the same as the 5v rail reading/s
See this for the rail voltage info
PSUs 101: A Detailed Look Into Power Supplies (Section 2.)
The original right hand window shows the machine running and is handy for that but for looking at the components in some detail close it and use the main left hand side panel
FOR OTHER COMPONENTS
PART B:
Open each small square with + in it on the section the components are in and then click on the individual component/s (it will highlight in blue) - in the right hand side will appear all sorts of details including brands speeds and other essential info that particular device. See pic for example.