Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Trim Not Enabled According to HDS?

26 Oct 2017   #1
WinningWith7

Windows 7 Ultimate x64
 
 
Trim Not Enabled According to HDS?

I have a Samsung SSD 850 PRO 256G which i reccently connected to a Syba SATA III 4 Port PCI-e x2 Controller Card and I installed the latest drivers and re-installs Intel RST because it crashed after adding the PCI card. I noticed in the PCI card boot sequence it said "PassThru AHCI"

According to Hard Disk Sentinal my TRIM is not enabled, perhaps because of the Marvel controller, but i was under the impression that TRIM/GC etc was done on the controller/SSD level and the drives performance is only at 80%

According to Samsung Magician I am getting close to double the speed when connected to the card vs my native sate 2 ports and it says

Is it dangerous to use the SSD on this PCI card like by causing crashes or wearing out the driver far sooner? Should i just connect normal hard drives to it?

Thanks




Attached Thumbnails
Trim Not Enabled According to HDS?-1.jpg  
Attached Images
Trim Not Enabled According to HDS?-2.jpg 
My System SpecsSystem Spec
.
26 Oct 2017   #2
torchwood

W7 home premium 32bit/W7HP 64bit/w10 tp insider ring
 
 

Hi Winningwith7,

have a look at this tutorial, does show you how to enable TRIM, and further info
.SSD Tweaks and Optimizations in Windows 7 - Windows 7 Help Forums


Roy
My System SpecsSystem Spec
26 Oct 2017   #3
Megahertz07

Windows 7 HP 64
 
 

- TRIM
Type this cmd
fsutil behavior query DisableDeleteNotify

It will give you one of two results, either a 0 or a 1. A zero indicates that TRIM is enabled correctly, a one means that it is not. If you have a TRIM-compatible SSD, but find that Windows 7 hasn't enabled the command, you can easily do so by running this command:

fsutil behavior set DisableDeleteNotify 0
My System SpecsSystem Spec
.

Reply

 Trim Not Enabled According to HDS?




Thread Tools




Similar help and support threads
Thread Forum
how to trim ssd
hi, using win7, just put in a new ssd drive, enabled trim in CMD, does trim run automatic or do i run it manual, i only have a defrag option that i know i must not use,defrag is set so it does not run, please help, some guys talk about using a optimize option, i can not find this on my...
Hardware & Devices
Verifying TRIM is enabled
I wish to confirm that TRIM is enabled on my PC (W7 Pro 64 bit). ACHI is enabled. The consistent advice I've found so far is to enter the following @ the command prompt: 'fsutil behaviour query DisableDeletNotify'. I get the response 'behaviour' is not a valid parameter. I've tried this...
Performance & Maintenance
How to TRIM a SSD in Windows 7
I know TRIM is enabled: C:\Windows\system32>fsutil behavior query DisableDeleteNotify DisableDeleteNotify = 0 but how do I tell the SSD to do the retrim like I can in Windows 8 with the defrag c: /o command? DO I need another program?
Performance & Maintenance
How to run TRIM
Havae just fitted a Crucial M4 and it is running like a misile, but cannot find out if it is runnig TRIM. A Google told me to run "fsutil behavior query disbaledeletenotify" but after a brief flash of the screen nothing happens. Am I doing something wrong.
Hardware & Devices
W7 64 TRIM for SSD
I know W7 supports TRIM but I need to if it is working on my SSD/HDD setups. I have a laptop and a PC where both have W7 64 installed on an SSD and Vista 64 installed on an HDD. When running W7, if I run fsutil.exe behavior query DisableDeleteNotify, it shows W7 has TRIM activated. TRIM will only...
Hardware & Devices


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 11:40.
Twitter Facebook Google+