Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: No artifacts when overclocking

09 Jul 2010   #11
imeem

Win 7 & 10 x64
 
 

Quote   Quote: Originally Posted by fishnbanjo View Post
Quote   Quote: Originally Posted by imeem View Post
Quote   Quote: Originally Posted by fishnbanjo View Post
In all seriousness you should be able to use autotune in CCC and it will tune it to the highest possible speed and stress it at the same time, you need to hit escape to end the testing and your clock ill be adjusted to optimal settings, i.e. fps, no artifacts and use of CPU. Other than that using Unigine Sanctuary at 1024x768 Full Screen, 3DMark06 and Vantage will show how the card responds to the autotune from CCC.
autotune freezes my computer after awhile.
That may be due to your drivers version, I have had good luck with CCC 10.3 and am testing CCC 10.6 in the next couple of days did not care for 10.4 and 10.5
I have driver version 10.6. It froze for me when I had 10.5 45 minutes into autotuning


My System SpecsSystem Spec
.
10 Jul 2010   #12
smarteyeball

 
 

Quote   Quote: Originally Posted by imeem View Post
Ok currently my HD 5770 is stable at 880 mhz and 1215 mhz with no lost of performance according to 3Dmark vantage and no artifacts when playing different games.. Should I continue increasing my memory clock (Can't increase gpu clock any further) and/or increase my voltage with msi afterburner as smarteyeball suggested?
If you are happy with current speeds - then increasing the memory doesn't have as much impact as increasing the core itself.

Keep in mind that extra volts = extra heat and there is still no guarantee that you will 'break the barrier'. Each chip has a wall, regardless of voltage

Quote:
Also is it good to test custom clock speed in CCC?
Personally, I've never bothered with it.

Quote   Quote: Originally Posted by imeem View Post
I have driver version 10.6. It froze for me when I had 10.5 45 minutes into autotuning
That's one of the reasons I don't use autotune. Clocks too high - insufficient voltage/wall = freeze.
My System SpecsSystem Spec
Reply

 No artifacts when overclocking




Thread Tools




Similar help and support threads
Thread Forum
Artifacts and BSOD (0x00000116) after Overclocking GPU
Hi everyone, A few days ago I overclocked my GPU (GTX 570) with MSI Afterburner app as I had done hundreds of times before (the GPU's almost two years old) and after pressing Ctrl + Alt+ Del to open Task Manager, the display went black and recovered a few seconds later showing a pop-up saying...
BSOD Help and Support
Artifacts on only 1 of 2 monitors
(I'm putting this in this forum because I'm fairly certain it's a monitor and not a graphics card issue) I have a dual monitor setup. One of them is a 19" 4:3 Eizo M1950 that is 5-6 years old. The other one is a 32" LG HDTV whose exact model currently escapes me. Recently I've started getting...
Hardware & Devices
Artifacts 30s after turning on...???
Got this problem, just started, allows me just enough time to get into my bios to check on system before computer locks. My voltage is 11.77, EVGA tech support said that this card needs between 11.9 to 12.2 voltage to run. Because only 11.77 volts with no load the tech support thought it might...
Graphic Cards
Artifacts and BSODS!
Hello all, Hoping someone can help/confirm a few things. This morning i go to my desktop computer (which was in sleep mode as always) click the mouse to bring it back to life and then i notice it's taking a bit longer than normal. Screen flashes black, i see the desktop then BANG BSOD...
BSOD Help and Support
How To: Overclocking Your AMD Processor : Introduction: The Basics Of Overclocking
http://media.bestofmicro.com/CPU-AMD-Overclocking,9-J-180487-1.jpg http://media.bestofmicro.com/CPU-AMD-Overclocking,9-K-180488-1.jpg Tom’s Hardware readers know all about overclocking, of course. In fact, many processor and graphics card reviews would be deemed incomplete without coverage of...
Performance & Maintenance


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 00:11.
Twitter Facebook Google+