Windows 7 Forums

Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: no sata in device manager

21 Jun 2009   #1
mark0159

Windows 7 RC1
 
 
no sata in device manager

Hey everyone. I am using windows 7 Rc1 7100 x86

hardware is asus a8n-sli motherboard which has a nforce4 sli chip set,
2x seagate hdd's
1 sata optical drive by LG

but anyway the problem I have is that windows 7 isn't showing any sata devices in the control panel (see attached picture)

while I was running vista I had downloaded and installed the correct drivers and didn't have a problem. I like win7 way more than vista so no going back.

I have done internet search for some drivers, found Fernandos_Vista&Win7_32bit_NF4-7_Test_Driverpack_v5.6 but they caused the machine to bosd. not helpful

I have also tried 15.23_nforce_winvista32_international_whql and had no luck what so ever.

so did see a couple of people say that win7 has built in drivers but if that's the case then why aren't these load

any help would be greatly appreciated




Attached Thumbnails
no sata in device manager-no-sata.png  
My System SpecsSystem Spec
.
21 Jun 2009   #2
nate42nd

Windows 7 Professional x64
 
 

I wonder if you need to enable the SATA controller in the BIOS. You may try that or get in there and see what the setting is. Good luck!
My System SpecsSystem Spec
21 Jun 2009   #3
Pendaws

Win7 SP1 + Ultimate 64 bit
 
 

I have the same Issue. I have been led to believe that the last 3 entries you have there are the SATA controllers? I have exact what you have. There is settings in the BIOS relating to SATA. One id the AHCI setting which is related to SATA and the other is the SATA native mode. I use an EP45 DS3R GB board and I enabled the SATA native mode but NOT the AHCI mode. The last setting ya need to set before you install an OS. Again, this is what I have been told.
My System SpecsSystem Spec
.

21 Jun 2009   #4
nate42nd

Windows 7 Professional x64
 
 

If you are not running a RAID configuration I believe enabling AHCI would be advantageous. You are running IDE otherwise. (if you're not using RAID)

I don't know if it would fix your problem but it may be worth a try.
My System SpecsSystem Spec
22 Jun 2009   #5
mark0159

Windows 7 RC1
 
 

thanks for your help but that option I don't have in my bios. In fact I don't have AHCI anywhere in my BIOS

anyway I hadn't touched my computer bios in going from Vista (where it was working fine) to windows 7.

due to the age of the motherboard, there isn't any updates. it's an Asus A8N Sli motherboard running an amd 939 chipset. I need to upgrade but having some troubles finding the gear that I want for the price that I want to spend.

Anyway I did a couple of screen dumps from the manual (which looks just like the real thing) and here you have 1, the first page where it will list date/time etc. As it stands with my computer, the two HDD's that I have will be listed on the first and second sata controller and the dvd drive on the 3rd. If you go in to each of those options for the device you get number 2, The only two options for Exteneded Drive is None and Auto. If I set the HDD on Sata 1 to None then I can't boot up. INSERT SYSTEM DISK AND PRESS ANY TO CONTINUE message. For Access Mode the only options you have is Large and auto. but this changes the cylinder size etc and have nothing to do with the access mode.

So moving right along I go in to chipset settings (Where you would expect these settings to live) and you get to number 3,
I have disabled IDE channel 0 and 1. I don't have a need for them and really don't see why they should be turned on.
IDE DMA transfer access only options are Enabled/Disabled. With this disabled I can't boot.
SATA Port 1, 2 Enabled/Disabled, enables and disabled the deivce.
SATA DMA Access is Enabled/Disabled. I thought that this might have been it. DMA is like IDE access, but again with this disabled I can't boot.

I have done things like loaded the setup defaults and again this has made no change.

I am really starting to think that this is just down to the motherboard being to old for windows 7.


Attached Thumbnails
no sata in device manager-1.png   no sata in device manager-2.png   no sata in device manager-3.png  
My System SpecsSystem Spec
22 Jun 2009   #6
nate42nd

Windows 7 Professional x64
 
 

I think you're right. It's too old. You might see if there's an update for that bios but even if there is.....you need more RAM and probably a new computer. You can get one pretty cheap on-line. $300 will get you one that you could use for a couple of years.

However if you have been running Vista....you should have no problem running Se7en it takes lees resources.
My System SpecsSystem Spec
22 Jun 2009   #7
mark0159

Windows 7 RC1
 
 

Oh I have no problems with running 7, in fact I'm not going to go back to Vista just because of this. I am going to be upgrading the hardware this year.

I am running 7 with only 2gb and 4gb page file and don't have any issues.

I would like faster access to my HDD, it's makes browsing all those thumbnails that much quicker. I would like to replace my hdd with SSD but hey dreams are free.
My System SpecsSystem Spec
Reply

 no sata in device manager




Thread Tools




Similar help and support threads
Thread Forum
Why does Device Manager say my SATA HDD is SCSI
The particular HDD is a Samsung HD103SI. This is a SATA drive. It is connected with a SATA cable. My PC doesn't have any SCSI ports. But Device Manager - Disk Drives lists it as SAMSUNG HD103SI SCSI Disk Device. It works just fine. Except for one thing, which I don't need at the moment. I...
Hardware & Devices
External drives show in Device Manager & Disk Manager but not Computer
Two of my USB external Hard drives, a Fantom 600 GB and a Western Digital My Book 500GB cannot be seen in My Computer. I can see them in Device Manager and that says that they are working properly and the drivers are up to Date. In Disk Manager the 2 external drives had a black bar unlike the...
Hardware & Devices
Unknown Device in Device Manager/Show Hidden Devices
I have a Toshiba laptop, model L505-ES5018. I had Windows 7 Home Premium 64 bit installed on here, but decided to reformat my hard drive using Windows 7 Ultimate 64 bit. After the reformat was finished, I ran Windows Update and it found several items to download and install for me. I noticed...
Drivers
Device Manager Code 19 Error for HP CDDVDW TS-H653T ATA Device
I am having an issue where my DVD/CD RW has a code 19 error in device manager. The drive still works as I used it to boot a Windows CD and run a startup repair to see if that found anything. I tried uninstalling the drive and then scanning and it failed to install the drive. I also tried...
Drivers
Bluetooth device not in device manager, no hardware switch, Acer netbk
Model is Acer Aspire One D270. Internal bluetooth doesn't work. Nothing in device manager. Fn+F3 is meant to control it, but doesn't. May be because I've messed with some programs. Trying to re-install to factory settings. Any suggestions at all? thanks D:
Network & Sharing
Device Manager reports Unknown Device & explorer crash
How do i figure out what driver or even component windows wants software for when in the device manager under other devices it lists an unknown device and windows update cannot find anything. Oh and is it appropriate for me to use this topic to ask another question regarding explorer.exe as...
Drivers


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 13:58.
Twitter Facebook Google+ Seven Forums iOS App Seven Forums Android App