New Fans.

Page 1 of 2 12 LastLast

  1. Posts : 2,393
    Microsoft Windows 7 Ultimate: x64 (SP1)
       #1

    New Fans.


    Hello,

    I just bought some Yate Loon fans, and it appears that there are no screws. And it also seems like, there's no screws following in my motherboard case. Do I really have to buy them myself?
      My Computer


  2. Posts : 4,466
    Windows 10 Education 64 bit
       #2

    Normally, no, they should be included with the fan. I have yet to buy a fan that didn't come with them. Consequently I now have tons of spares from replacing worn out fans.
      My Computer


  3. Posts : 2,393
    Microsoft Windows 7 Ultimate: x64 (SP1)
    Thread Starter
       #3

    alphanumeric said:
    Normally, no, they should be included with the fan. I have yet to buy a fan that didn't come with them. Consequently I now have tons of spares from replacing worn out fans.
    I wish you could trade them :)
      My Computer


  4. Posts : 1,074
    Windows 7 Profession 64-bit
       #4

    You might consider some Fan Vibration Isolating Mounts.
      My Computer


  5. Posts : 2,393
    Microsoft Windows 7 Ultimate: x64 (SP1)
    Thread Starter
       #5

    Digerati said:
    You might consider some Fan Vibration Isolating Mounts.
    Yeah that's basically what i'm looking for. Actually it's quite bad that Yate Loon didn't warn me about such things.

    Thanks ^^
      My Computer


  6. Posts : 1,074
    Windows 7 Profession 64-bit
       #6

    Actually it's quite bad that Yate Loon didn't warn me about such things.
    I guess they figure most users have a big stash of screws for drives, fans, motherboards, etc. laying around. I have tons. Strip an old case or two and you will too. I actually like those isolating mounts - not only do they ensure any fan vibration does not resonate through the case, but they don't cut threads into the metal like regular fan screws do (same with some heatsink fans). When you use a screw to cut threads, the "cuttings" or tiny metal filings have the potential to end up bouncing around inside your case - particularly when you remove the screw. Something about metal filings bouncing around inside electronics just does not sound right to me!
      My Computer


  7. Posts : 4,466
    Windows 10 Education 64 bit
       #7

    All the fan screws I have screw into the plastic fan frames, not the case? I've been contemplating getting some of those isolation mounts. The fan in the front of my case is quit loud and needs to be replaced. To get the screws out I have to remove the whole front panel of the case. If it wasn't such a pain I'd have done it by now. Using those rubber mounts should be a lot easier and I'd never have to touch a screwdriver.
      My Computer


  8. Posts : 2,393
    Microsoft Windows 7 Ultimate: x64 (SP1)
    Thread Starter
       #8

    Got the problem solved with strips.

    Now, is it possible to go from 12V to 5V in BIOS? And is it riskable? Is it possible again, in BIOS, with no controler and sutff like that?
      My Computer


  9. Posts : 1,074
    Windows 7 Profession 64-bit
       #9

    Now, is it possible to go from 12V to 5V in BIOS?
    No. Why would want to do that? Many devices (fans and drives, for example) need 12V to run.
      My Computer


  10. Posts : 2,393
    Microsoft Windows 7 Ultimate: x64 (SP1)
    Thread Starter
       #10

    Digerati said:
    Now, is it possible to go from 12V to 5V in BIOS?
    No. Why would want to do that? Many devices (fans and drives, for example) need 12V to run.
    It's just quite noisy. Not to mention really noisy. I don't know if it's because it isn't installed right, maybe there's a little space, there and there.
      My Computer


 
Page 1 of 2 12 LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 07:24.
Find Us