SSD newly installed

Page 1 of 2 12 LastLast

  1. Posts : 24,479
    Windows 7 Ultimate X64 SP1
       #1

    SSD newly installed


    I just installed a SSD, Crucial M4 64GB, which for now is connected via a SATAII header. If connected to the SATAIII, where it should be, it, or any drive, appears as a USB card with the Safely Remove icon.With it on SATAII it doesn't get the most performance. Any drive on SATAII shows as a normal HDD in computer. I have a 320GB HDD on the SATAIII header for storage in this snip.Performance seems a bit off for a SSD too, but I think that will improve after TRIM has more time to work.
    SSD newly installed-computer.pngSSD newly installed-safelyremove.png

    SSD newly installed-ssd.png
      My Computer


  2. Posts : 1,781
    Windows 7 Professional SP1 32-bit
       #2

    The "eject devices" icon is actually perfectly normal if you're running in AHCI mode, because of the hotplugging feature that comes with it. Since you'll never unplug your OS drive of course (and it probably wouldn't let you anyway), just ignore the icon.

    You say it doesn't appear with devices connected to the SATA-II ports vs. SATA-III. That makes me wonder if you have separate BIOS settings to configure either one as IDE or AHCI, independently of the other.
      My Computer


  3. Posts : 1,846
    Windows 7 Ultimate x64, & Mac OS X 10.9.2
       #3

    did you have both drives plugged in when you changed to AHCI and installed windows?
    Some people have had issues.
      My Computer


  4. Posts : 4,161
    Windows 7 Pro-x64
       #4

    I think you have that drive K connected to an ESATA port. That will automatically treat it as hot-swap.
      My Computer


  5. Posts : 4,161
    Windows 7 Pro-x64
       #5

    Is this one of those Frankenstein boards with two drive controllers?

    I looked at a photo of your board and couldn't find the SATA3 ports. Are they white and laid on their side?
    Attached Thumbnails Attached Thumbnails SSD newly installed-britton-board-2.jpg  
      My Computer


  6. Posts : 26,863
    Windows 11 Pro
       #6

    Gary, plug it into the sata3 port and see what happens. It should boot fine, just check it in bios. Open As SSD and dont run the test, just look at the top left and see what driver it shows.
      My Computer


  7. Posts : 24,479
    Windows 7 Ultimate X64 SP1
    Thread Starter
       #7

    Corazon said:
    The "eject devices" icon is actually perfectly normal if you're running in AHCI mode, because of the hotplugging feature that comes with it. Since you'll never unplug your OS drive of course (and it probably wouldn't let you anyway), just ignore the icon.

    You say it doesn't appear with devices connected to the SATA-II ports vs. SATA-III. That makes me wonder if you have separate BIOS settings to configure either one as IDE or AHCI, independently of the other.
    I have aboth drives connected to SATA AHCI, only the K has the Safe to remove. It is SATA III, my eSATA ports are on the back of the mobo.

    carwiz said:
    Is this one of those Frankenstein boards with two drive controllers?

    I looked at a photo of your board and couldn't find the SATA3 ports. Are they white and laid on their side?
    Yes, actually 3 contollers, JMicron, Marvell, and GSata. One for SATA II, SATA III, and yet another for eSATA. Yes the SATA III are those white ones.
      My Computer


  8. Posts : 1,781
    Windows 7 Professional SP1 32-bit
       #8

    Sounds to me like your SATA-II simply doesn't have the hardware support for hotplugging. Which makes sense as it's much more useful for your eSATA ports.
      My Computer


  9. Posts : 1,846
    Windows 7 Ultimate x64, & Mac OS X 10.9.2
       #9

    All sata3 controllers are different from sata2.
      My Computer


  10. Posts : 4,161
    Windows 7 Pro-x64
       #10

    badger906 said:
    All sata3 controllers are different from sata2.
    Not really. Intel does it with one. It's part of the Platform Controller Hub. Only one driver set is needed. Motherboards that have multiple controllers need a driver set for each. In the above case, Marvell drivers AND Micron drivers depending on which controller is used. If you use both, then both driver sets are needed. If the ESATA is on a separate controller, then it too needs a driver set.
      My Computer


 
Page 1 of 2 12 LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 00:19.
Find Us