Disk Checking Error on Windows Startup


  1. Posts : 5
    ATI Mobility RADEON HD 4330
       #1

    Disk Checking Error on Windows Startup


    Hello Everyone,

    I recently had an external USB hard drive go faulty on me. It would no longer spin up correctly and my Dell PC would no longer recognise the device. It would attempt to install drivers for it, but fail. I've written off the hard drive (fortunately I had the data backed up).

    However, since this event every time I start up my PC I get a disk checking message pop-up for an obscure disk volume. This test subsequently fails (see attached image).

    I can skip the test and start up my PC fine, but it's getting very annoying. I've also done a disk check on my C drive which went through ok.

    Is there anyway to disable this disk check?

    Thanks in advance.
    Attached Thumbnails Attached Thumbnails Disk Checking Error on Windows Startup-imag0056.jpg  
      My Computer


  2. Posts : 10,994
    Win 7 Pro 64-bit
       #2

    Hello ktpanks2 and welcome ot Seven Forums.

    This may be nothing more than resetting the check disk to not run at startup.

    Check Disk - Reset

    But sometimes when a drive is not safely disconnected (and a catastrophic drive failure could be in this category) other files including files on the C: drive can become unreliable or suffer from "dirty bits". This previous Forum thread explains more:

    Hard Drive Error: Volume is dirty 0x80071AC3

    And it wouldn't hurt to also check for damaged or corrupt system files by running a system file checker scan from an elevated command prompt (option two.) If problems are found, run the scan 3 times and immediately reboot the computer after each scan.

    SFC /SCANNOW Command - System File Checker
      My Computer


  3. Posts : 5
    ATI Mobility RADEON HD 4330
    Thread Starter
       #3

    Many thanks for your reply. I'll try these suggestions when I get home tonight.

    Just off the top of my head though I'm a little confused how I can force Windows to skip the test given it's not being reffered to by a specific drive letter, e.g. C: - rather I see \\?\volume.....

    But I'll have a little play around later and let you know how I get on.

    Katie
      My Computer


  4. Posts : 10,994
    Win 7 Pro 64-bit
       #4

    Katie, my apologies for missing that bit of information in your screen capture. Upon taking a closer look I noticed that it refers to "Volume Label is RECOVERY." RECOVERY is usually a hidden partition on the C: drive and is put there by the computer manufacturer. It usually doesn't have a drive letter assigned so that's probably why you're getting the ?\Volume designation. Hopefully you can just choose C: as the drive to check.

    Again, my apologies for missing this.
      My Computer


  5. Posts : 10,796
    Microsoft Windows 7 Home Premium 64-bits 7601 Multiprocessor Free Service Pack 1
       #5

    Assign a drive letter to partition recovery. Post screenshot of disk management. Don't reset chkdsk becuase there's something wrong with partition RECOVERY. Assume you assign drive letter W to it. Do from elevated command prompt:

    Code:
    fsutil  dirty  query  W:
    Can you explore W using windows explorer?

    Post results.
      My Computer


  6. Posts : 5
    ATI Mobility RADEON HD 4330
    Thread Starter
       #6

    Hi,

    I was able to assign a drive letter to the RECOVERY partion (I was also able to explore via windows explorer). I then ran the query as above ...

    Microsoft Windows [Version 6.1.7601]
    Copyright (c) 2009 Microsoft Corporation. All rights reserved.
    C:\Windows\system32>fsutil dirty query w:
    Volume - w: is Dirty
    C:\Windows\system32>

    So the volume is dirty.

    I'll try some of the other suggestions above now.
      My Computer


  7. Posts : 5
    ATI Mobility RADEON HD 4330
    Thread Starter
       #7

    Ok cool. Having assigned a drive letter to the partition I was able to run a chkdsk on it. Upon completion I was able to re-run the above query and the volume was no longer dirty.

    Upon reboot I didn't get the error I was seeing previously.

    Looks like I'm sorted.

    Any recommendation on what should I do with this w: partition now?
      My Computer


  8. Posts : 5
    ATI Mobility RADEON HD 4330
    Thread Starter
       #8

    Disk management screenshot ...
    Attached Thumbnails Attached Thumbnails Disk Checking Error on Windows Startup-diskman.jpg  
      My Computer


  9. Posts : 10,994
    Win 7 Pro 64-bit
       #9

    The recovery partition is provided by the computer manufacturer as a way to restore the computer to factory specs. You could just leave it as is for now since there's no immediate need to use it. If you've made a set of recovery disks (usually recommended by the manufacturer) you could format that partition and make it 19+GB of unallocated space . You could then assign that unallocated space to the C: partition and increase it by the 19+ GB. But since youve got a 1TB hard drive the extra 19GB isn't going to add all that much.

    So I think I'd leave everything as is, at least for a while to make sure the computer really is working properly.
      My Computer


  10. Posts : 10,796
    Microsoft Windows 7 Home Premium 64-bits 7601 Multiprocessor Free Service Pack 1
       #10

    chkdsk ran on startup because RECOVERY was dirty. Volume was a little bit corrupt. But why??? You never use it. And chkdsk can also repair volumes without a drive letter. Remove drive letter W using disk manager, so everything is as it was before
      My Computer


 

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 01:43.
Find Us