HP Pavilion DV6 AHCI issue


  1. Pendaws
    Posts : 185
    Win7 SP1 + Ultimate 64 bit
       New #1

    HP Pavilion DV6 AHCI issue


    I have an issue with a HP laptop that I find annoying.

    The laptop belongs to a customer's Son and he brought it to me because it ran rather slow and so, I looked at it and told him that some more memory and a nice SSD would be good for him, anyway, the main issue here is the silly Setup in the BIOS.

    I went to the trouble of getting the NEWEST BIOS update from HP and installed it. He wanted to have Win 7 on it again and so I installed it from a USB drive and it went flawlessly but, after setting all of it up I added the Samsung Magician software for some performance tweaking. the first thing I cam across was that the software said that AHCI wasn't active and that it couldn't tell what type of SATA it was. I have posted a question on HP forum but I hold no great hope of an answer but, you never can tell??

    According to HP the driver that is loaded by the RST programme is sufficient for it but, it's a SATA/RAID driver and that appears to be what is causing the issue with Magician. I have seen a few articles on HP's site about this issue and they say it is ok but, obviously it isn't. There is no section in the device manager for IDE/ATA ATAPI the driver is shown in the storage section instead. Which, is where, the RAID driver usually ends up.

    I am worrying for nothing or? I find it strange that a laptop that can ONLY handle a single drive would be setup for RAID?? I have seen this same silly thing before with Lenovo and Toshiba where they used raid config for the HDD, but they weren't SSD's.

    I thought that this might have some smart people coming along to see and maybe have an answer? :)
      My Computer
    Quote Quote

  3. georgeks
    Posts : 177
    Windows 10 Pro x64
       New #2

    Pendaws the RAID term refers to the way the HDD is accessed.

    AHCI - Advanced Host Controller Interface - this is a hardware mechanism that allows the software to communicate with Serial ATA (SATA) devices. It offers features such as hot-plugging and native command queuing (NCQ).


    IDE - Integrated Drive Electronics - IDE is basically the "old" version of AHCI without hot-plugging and NCQ. (This is usually used during the Parallel ATA (PATA) era hard disks)


    Now. AHCI mode and IDE mode -- what is it? IDE mode is to give you the greatest compatibility with older operating systems. While AHCI is as I mentioned above, modern version of the IDE -- use AHCI mode if you are running recent operating systems (Windows Vista+ and Linux kernel from 2.6.19+). IDE mode will allow you to connect older operating systems to SATA drives.


    As I mentioned above, SATA is Serial ATA, and is the replacement for Parallel ATA (PATA) hard drives.


    RAID - This is a storage technology where you combine multiple disks into a "single" unit, depending on the mode, there can be RAID-0 through RAID-6, and each with different configurations of the hard drive. I'll just explain the simple examples: RAID-0 which is striping but no parity or mirroring, this means there is no redundancy for data, If there is a failure on one disk, it will cause the data loss of the entire RAID array. Ex: You have 0110 as data to be written, 01 will go on Disk 1, and 10 will go on Disk 2, allowing for faster read/write access to the data.


    RAID-1 - This is the opposite of RAID-0, which is mirroring without striping (no parity either). This basically means you have an exact clone of Disk 1 on Disk 2, in case Disk 1 fails.


    RAID0+1 does both what RAID 1 and 0 does, that is to say striping (writing data simultaneously to two [or more] drives. plus mirroring in case of failure) the minimum amount of drives required for this type of setup is 4 IDENTICAL drives.


    There are also RAID 2, 3, 4, 5 ,6. Which is just more implementation of different configurations of striping/parity/mirroring across drives.


    That being said, your RAID mode will allow you for some type of RAID configuration, should you choose to do so.


    Supplemental: Many SATA controllers can enable AHCI separately or in conjunction with RAID support. Intel recommends choosing RAID mode on their motherboards, which also enables AHCI, rather than AHCI/SATA mode for maximum flexibility (in case you ever want to build a RAID array), since there are some issues that occurs, usually BSOD, when you choose a different mode once an operating system has already been installed.
      My Computer
    Quote Quote

  4. Pendaws
    Posts : 185
    Win7 SP1 + Ultimate 64 bit
    Thread Starter
       New #3

    Well, RAID mode is impossible to use in this laptop. The laptop is different to a Desktop as the BIOS is very much different.
    I do know about the IDE, SATA, AHCI, RAID, been using computers since the late 1980's
    When I originally setup this laptop, the setting in the registry for AHCI start came up as a "3" and not "0" like it should
    and, in the device manager, there is no group for IDE/ATA/ATAPI but is listed in storage controller and it makes a slight
    difference to a computer that is able to set the AHCI mode separately.

    Oh well, I guess it will remain one of the mysteries of Computers, thanks anyway. :)
      My Computer
    Quote Quote

 

  Related Discussions
Blue Screen issue on HP Pavilion G6
in BSOD Help and Support

Hi everybody, I was working on my PC and suddenly I felt like the laptop got overheated it got restarted. I turn it on again and while it was booting up right after the loading screen my computer crashed and the BSOD error popped up for abuth 20seconds and it rebooted itself again. After reading...
Hello, See my system specs for my laptop make and model. I cannot get the audio driver to install. I have tried two drivers from the HP website that it recommended for this model (sp55094.exe and sp51637.exe) as well as allow Windows Update to locate it for me. It's not working. It is an IDT...
AHCI Issue
in Hardware & Devices

Hey Techies... I need some information regarding the convertion of SATA to AHCI. I have built a new PC with i5 2500K,Asus P8Z77 M Pro Motherboard and 8GB Transcend RAM. I tried to install Windows 7 ultimate after formatting my old hard disk(Segate Bracuda 500 GB).I got an error as "Enable...
I have an HP pavilion p6-2000ukm and recently had to format it after system restore stopped working. As per the standard format, I then reinstalled all my drivers, however, every time I try to reinstall the graphics driver i get the blue screen of death after rebooting with the following message ...
Good evening all. We just replaced my wife's failing Apple iMac with an HP Pavilion Slimline computer. We took it out of the box today and set it up around 5 P.M. Shortly after setup, 5 crashes occurred by 10:30 P.M. Posted below is information from the crash log as well as the dump file. If...
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

 © Designer Media Ltd
All times are GMT -5. The time now is 18:45.
Find Us