Error message at boot : Hard Disk:SMART Status Bad, Backup and replace

Page 3 of 4 FirstFirst 1234 LastLast

  1. Posts : 68
    Windows 7 Professional 64 bit SP1
    Thread Starter
       #21

    Hi jumanji. I'm in the midst of the ddrescue and so far there have been no errors. I'm writing a recovery map file as well. My question is, if I interrupt with Ctrl-c, will I be able to switch off the computer and resume? Or will it have to be switched on throughout?
      My Computer


  2. Posts : 2,774
    Windows 7 Professional 64-bit
       #22

    shank said:
    ...in the midst of the ddrescue...if I interrupt with Ctrl-c, will I be able to switch off the computer and resume? Or will it have to be switched on throughout?
    My educated guess is: leave computer on until it is finished.
      My Computer


  3. Posts : 68
    Windows 7 Professional 64 bit SP1
    Thread Starter
       #23

    Ok after running it overnight, it seems like it would take months to complete. Only had done 7GB in 14 hours. So I ctrl-c to interrupt. Booted into Windows and wasn't able to see the new hdd in My Computer, but it was there in Disk Management. Is there some way to see what has been recovered in that disk?
      My Computer


  4. Posts : 68
    Windows 7 Professional 64 bit SP1
    Thread Starter
       #24

    Here is a screenshot of my Disk Management Window :

    Error message at boot : Hard Disk:SMART Status Bad, Backup and replace-capture.jpg
      My Computer


  5. Posts : 7,055
    Windows 7 Home Premium 32 bit
       #25

    With ctrl+c you can pause and then resume as long as you do not shut down the computer.

    If you shut down the PC, the logfile written into the RAM drive is lost and therefore you cannot resume.(The whole ddrescue runs from the RAM drive.If you want the logfile to be written into some other media like another HDD or pendrive you have to take the help of some one proficient in Linux who can write the correct command for it in the command string)

    In the WDM screenshot you posted, you can try assigning drive letters to the partitions shown as healthy and check whether they show up thereafter.
      My Computer


  6. Posts : 68
    Windows 7 Professional 64 bit SP1
    Thread Starter
       #26

    Hi Jumanji. That Disk 0 is actually the destination drive that I was cloning to. I'm not able to assign drive letters to the healthy partitions.
      My Computer


  7. Posts : 7,055
    Windows 7 Home Premium 32 bit
       #27

    Best is to run ddrescue to its completion, without shutting down the PC . Beyond that I cannot advise you any further.-

    BTW, what command options are you using? Just curious.
      My Computer


  8. Posts : 68
    Windows 7 Professional 64 bit SP1
    Thread Starter
       #28

    I have decided to cut my losses and just retire the drive. Like you mentioned before, the risk-reward ratio is nil, as the remaining time was in months!

    What I intend to do now is use that disk 0 as a normal HDD in my computer. That's why I wish to solve this disk not showing up.

    I used ddrescue -d -f -r3 /dev/sdb2 /dev/sdc recovery.mapfile , where sdb2 was the C partition of my damaged drive.
      My Computer


  9. Posts : 7,055
    Windows 7 Home Premium 32 bit
       #29

    OK.

    Now I remember. On your bad drive the first sector is bad.

    Now only the bad sector has been written/cloned to the destination drive.

    Run PW. On the left Pane click on "Rebuild MBR" and then "APPLY". This will write the MBR code into sector 0 of the new destination drive.

    Next run Partition Recovery Wizard Quick Scan, select all the found partitions, Finish and Apply to write the partition table into sector 0.

    After that try to assign the drive letters to the healthy partitions and Apply.

    If all this does not help/is not executable ......give up.

    As for the bad source drive the first sector, the heart of the drive is dead. That drive is now a scrap. There is no way you can use it. >>>>>>into the electronic waste bin.

    For the new destination drive, you can delete all the partitions to make the whole drive unallocated and then format it.

    If for some reason it is not possible, run a low level format using the HDD Low level Format Tool HDDGURU: HDD LLF Low Level Format Tool that will completely wipe the drive. You can then initialise it and do a regular format. Make sure you wipe the correct drive.(Remove all other external drives/pendrives so that you do not accidentally wipe those)
    Last edited by jumanji; 24 Jun 2016 at 14:34.
      My Computer


  10. Posts : 68
    Windows 7 Professional 64 bit SP1
    Thread Starter
       #30

    jumanji said:
    OK.

    Now I remember. On your bad drive the first sector is bad.

    Now only the bad sector has been written to the destination drive.

    Run PW. On the left Pane click on "Rebuild MBR" and then "APPLY". This will write the MBR code into sector 0 of the new destination drive.

    Next run Partition Recovery Wizard Quick Scan, select all the found partitions, Finish and Apply to write the partition table into sector 0.

    After that try to assign the drive letters to the healthy partitions and Apply.

    If all this does not help ......give up.

    As for the bad source drive the first sector, the heart of the drive is dead. That drive is now a scrap. There is no way you can use it. >>>>>>into the electronic waste bin.
    I shall try what you mentioned Jumanji. Just to clarify, PW refers to Partition Wizard, right? And Partition Recovery Wizard is just a wizard in that same program?

    P.S. If this doesn't work, I can still wipe out the drive and use it as per normal ?
      My Computer


 
Page 3 of 4 FirstFirst 1234 LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 00:24.
Find Us