Hard Disk asks to initialize, shows no partitions and "Bad Disk" in PW

Page 1 of 3 123 LastLast

  1. Posts : 16
    Windows 7 Professional x64
       #1

    Hard Disk asks to initialize, shows no partitions and "Bad Disk" in PW


    Hello,

    This is my first post on this forum. I've used it many times before, reading about subjects I needed to know at that time, since it has very useful information! So thanks for this forum and everybody who contributes!

    My hard disk stopped showing up in windows explorer. It does show up in BIOS and disk management as Seagate Backup Plus. In disk management it tells me to initialize the disk.
    This happened after I was copying a lot of files from my hard disk to another 2 TB Seagate hard disk. Mine is 4TB. It got stuck, hanged while busy. I kind of forgot what I did exactly afterwards, any of the following, maybe a combination:
    1. I terminated the process in task manager
    2. I unplugged the device(s)
    3. I restarted the laptop
    4. (If the whole laptop was hanging, don’t really remember if that was the case) I turned it off by holding the power button.

    After that the above situation happened.

    Before I did any of the above things, when the process was still hanging, I could hear my HDD making some strange noises. It was not very loud, but some repeated strange soft noises. This worried me a little. I hope the hardware is not damaged, but I suppose that would still be good, since it does show up.

    My HDD is also very full, and I mean very, very full. I have 4 partitions. Some partition are like full with only a few MB’s left. The one I was copying from had a few GB’s left.

    Ok, so then I spend hours reading about this to try to find a solution. There were quite some things, but also a lot of things contradictory or not fully satisfactory to my opinion. I also read some threads and posts on this forum, mainly from Jumanji, which all had good info. So thanks again for this!
    Since there was no definite satisfactory solution in my opinion I did not want to try things out in case I would mess it up even worse. So that’s why the thread.

    From what I’ve read I think the partition table is damaged. I’ve downloaded MiniTool Partition Wizard Free v10.2. I wanted to try the “Partition Recover”, but then I read on their website that if you had a GPT disk and it now shows as MBR, which is my case, you should first change it to GPT. But my disk is not showing anything, it just says “Bad Disk”. Right mouse click is not possible and on the left side nothing is showing up, so I’m not able to change it to GPT. So I also didn’t try to Recover Partition, because I thought I might mess it up.
    By the way, Disk Management says at “Partition Syle: Not applicable”

    I also read Jumanji say in some posts that if PW says Bad Disk it usually is not retrievable. But then why is it showing up? Well I hope it’s not so bad.


    Sorry for the longwinded question (without even a real question posted :P). But I always tend to write extensively to make the other really understand what I mean.

    So the question: Can somebody help me with this? What should I do?

    I am currently travelling, so I might respond a little late. Actually I usually respond a little late even when not travelling :P

    I appreciate are your help, time and effort. Thanks a lot in advance!
    Attached Thumbnails Attached Thumbnails Hard Disk asks to initialize, shows no partitions and "Bad Disk" in PW-bad-disk-seagate-backup-minitool-partition-wizard-free.png   Hard Disk asks to initialize, shows no partitions and "Bad Disk" in PW-initialize-seagate-backup-disk-management.png   Hard Disk asks to initialize, shows no partitions and "Bad Disk" in PW-unallocated-seagate-backup-disk-management-without-partition-style.png  
      My Computer


  2. Posts : 1,784
    Linux Mint 18.2 xfce 64-bit (VMWare host) / Windows 8.1 Pro 32-bit (VMWare guest)
       #2

    I suggest you boot into Linux Live and then try to read the hard drive from within Linux. Sometimes Linux does a better job of reading a disk than Windows does.

    Although I don't think the error resulted from the drive being totally full, still, it would be good to free up some space on it. Who knows, you might get lucky from freeing up some space - the drive may start working again.

    If reading the drive in Linux fixes it, great. But it may not. Your only solution might be to copy everything off of the drive, delete all of the partitions currently on it, create new partitions, and format them. (Choose "NTFS" for these two operations.) You can do the formatting and partitioning in Linux using GPARTED. Just be careful that you don't repartition your Windows drive!

    Once you have fixed the drive, boot back into Windows and check it out.
      My Computer


  3. Posts : 3,783
    win 8 32 bit
       #3

    The first step is go to the makers site they normmaly have a bootable test for their drives which is specific to their drives and will tell you if the disk is faulty. Its the best tool as its made for their drive
      My Computer


  4. Posts : 16
    Windows 7 Professional x64
    Thread Starter
       #4

    Thanks for your quick replies and the info.
    @mrjimphelps

    I forgot to mention. I had already tried it on Ubuntu Studio, since I knew Linux sometimes handle these things better. But to no avail. I can feel it spinning, but it doesn't show up..
    If there is any Ubuntu solution to this problem I would be happy to know. Any way I can fix this is highly appreciated.
    You say to copy everything of the drive. But that would only be possible if it is readable right?
    I have read somewhere a while ago about making a whole image of the disk so you are able to do several trials of data recovery without loosing/corrupting your data in the process. Are you talking about this?
    This could be an option if nothing else works. But preferably I would like to have this disk working again, preferably in the folder structure it was. For now I also don't have money to buy a new hard disk to make a system image. Also I'm travelling at the moment. And all the other hard disks I have at home are smaller than 4TB and as far as I know you need at least the same size to do a disk image.

    Another thing I forgot to mention. It is a external hard disk and I use it mainly to store data and some system images.
    @samuria
    Good point. I downloaded Seatools for Windows and am scanning through their manual now and read a piece on Lifewire. It seems nice :)
    One thing though, not sure about it, but I think read somewhere that if you subject a (maybe) faulty drive to a diagnostic test it might overburden the drive and cause more havoc. Is this true?
    Anybody any experience with Seatools? Which test should I use if I do, since it has a lot of them?
    Last edited by Bad Wolf; 26 Mar 2018 at 15:21.
      My Computer


  5. Posts : 3,783
    win 8 32 bit
       #5

    THe makers make the tool for their drive so its perfectly safe you may also need that report if the drive is under warrenty. Its no good trying anything else until you know the results of their scan
      My Computer


  6. Posts : 7,055
    Windows 7 Home Premium 32 bit
       #6

    It is very difficult to say what exactly happened in your case. ( It is also true in most cases and so we work mostly on presumptions and assumptions but all the while taking precautions that whatever we do we do not cause any further damage to the data. It is almost a tight ropewalking. At times we may fail to complete it too )

    1. In this case you have been rightly advised to run Seatools and check the health of the drive. Go through the documentation on how to use it. Run the short Test and if it fails run the long test and post the results. disk 1 is unknown, not initialized, unallocated - Page 14 - Windows 7 Help Forums

    2. Depending upon when your 4TB external HDD was bought, it could be an MBR drive. PW shows it as an MBR drive. So do not initialise it as a GPT drive.

    3. Read the label on your 4TB Seagate External drive and post the exact model number to determine whether it is a 2.5" HDD inside or a 3.5 HDD inside. Date of Purchase? After purchasing it did you format it anytime? Is it still under warranty?
      My Computer


  7. Posts : 16
    Windows 7 Professional x64
    Thread Starter
       #7

    @samuria
    Yes, it makes sense :)
    And true about the test results needed for warranty.
    @jumanji
    Thanks for your input :)

    1. I did both tests:

    Short Generic Test

    --------------- SeaTools for Windows v1.4.0.6 ---------------
    31-Mar-18 04:27:23
    Model: BACKUP+
    Serial: 07CA5434BF97
    Firmware: 0304
    Identify - Started 31-Mar-18 04:27:23
    Identify - Started 31-Mar-18 04:31:31
    Model: BACKUP+
    Serial: 07CA5434BF97
    Firmware: 0304
    Model Number: ST4000LM016-1N2170
    Serial Number: W800AZ1F
    Firmware Revision: 0003
    Drive Capacity: 4.14 GB / 3.86 GiB
    Max LBA: 8089949
    Cache Size: ----
    Power-On Hours: 0
    Drive Temperature (C/F): 0 / 32
    WWN: 5000C5008BACA3B4
    Sector size (Logical/Physical/Allignment): 512 / 512 / 0
    Rotation rate: 7200 RPM
    Form factor: ----
    Specification Supported: ATA8-ACS
    Encryption Support: Not Supported
    Security Mode: Supported
    SMART: Enabled
    Host Protected Area features: Enabled
    Advanced Power Management: Not Supported
    Download Microcode: Segmented
    Short DST - Started 31-Mar-18 04:34:52
    Short DST - Pass 31-Mar-18 04:35:52
    Short Generic - Started 31-Mar-18 04:37:39
    Short Generic - FAIL 31-Mar-18 04:38:37
    SeaTools Test Code: 6C9AC2A4


    Seatools Long Generic Test fail code

    --------------- SeaTools for Windows v1.4.0.6 ---------------
    31-Mar-18 04:27:23
    Model: BACKUP+
    Serial: 07CA5434BF97
    Firmware: 0304
    Identify - Started 31-Mar-18 04:27:23
    Identify - Started 31-Mar-18 04:31:31
    Model: BACKUP+
    Serial: 07CA5434BF97
    Firmware: 0304
    Model Number: ST4000LM016-1N2170
    Serial Number: W800AZ1F
    Firmware Revision: 0003
    Drive Capacity: 4.14 GB / 3.86 GiB
    Max LBA: 8089949
    Cache Size: ----
    Power-On Hours: 0
    Drive Temperature (C/F): 0 / 32
    WWN: 5000C5008BACA3B4
    Sector size (Logical/Physical/Allignment): 512 / 512 / 0
    Rotation rate: 7200 RPM
    Form factor: ----
    Specification Supported: ATA8-ACS
    Encryption Support: Not Supported
    Security Mode: Supported
    SMART: Enabled
    Host Protected Area features: Enabled
    Advanced Power Management: Not Supported
    Download Microcode: Segmented
    Short DST - Started 31-Mar-18 04:34:52
    Short DST - Pass 31-Mar-18 04:35:52
    Short Generic - Started 31-Mar-18 04:37:39
    Short Generic - FAIL 31-Mar-18 04:38:37
    SeaTools Test Code: 6C9AC2A4
    Long Generic - Started 31-Mar-18 04:58:36
    Long Generic - FAIL 31-Mar-18 04:59:35
    SeaTools Test Code: 6C9AC2A4


    2. Bought around Jan 2015. As far as I can remember it has always been GPT. (I might be wrong though).

    3. Bought around Jan 2015.
    External Hard Disk info:

    Seagate 4TB Backup Plus


    S/N: NA7P5B0L
    P/N: 1K9APV-500
    Model no: SRD00F1

    I think it is a 2.5". I might have formatted it, I don't remember that well. I did have 4 partitions and I think it always asks to do a format after making a partition.
    Seagate's website says it has no more warranty.
      My Computer


  8. Posts : 7,055
    Windows 7 Home Premium 32 bit
       #8

    If it is not under warranty any longer, you can try to pullout the HDD from the enclosure, connect it directly to the motherboard SATA connector in a desktop or place it inside a working external case and check whether your HDD is OK. You may rerun Seatools and check the health of the HDD.

    If it is only the SATA to USB adapter fault, the HDD may still be alright.

    Seagate backup plus portable Drive SRD00F1 ST1000LM035 100809471 repair data recovery - YouTube

    Seagate Expansion Portable Drive SRD00F1 Opening Uncasing - YouTube

    How to open a Seagate Backup Plus Drive - YouTube

    Note: If your external HDD was originally initialised as a GPT drive, you may be able to read the drive straight away. If on the other hand if your original HDD came formatted as an MBR drive, You may not be able to retrieve the data even if the HDD passed the seatools test. We may have to run TestDisk, change the sector size and then copy the data to another drive. Either way data can be recovered if the HDD (outside its enclosure) passes the Seatool test.
    Last edited by jumanji; 01 Apr 2018 at 21:16.
      My Computer


  9. Posts : 16
    Windows 7 Professional x64
    Thread Starter
       #9

    Do you think it is a SATA to USB adapter fault? If so, on what basis?
    I would prefer not to mess around with the hardware too much, e.g. opening the case. One reason being that if I do need to send it to a data recovery centre (which I hope I don't have to) they charge insanely more if the media is tampered with. I'm not sure if only opening the case is also considered tampered or not. But still they will be able to see it is messed with.

    Are they any other options or possibilities?

    At the moment I don't have access to a desktop. I only have a laptop with me.


    I had another look at the SeaTool test results and noticed that the data is incorrect, e.g. my serial number and model are wrong. But then again, the test code also indicates that it is not able to recognize the serial number.

    Shouldn't I be doing some other tests, like SMART? Or will that only damage it more/have no benefits?

    And how come my laptop is able to recognize the disk if there is a hardware problem, e.g. SATA to USB adapter?
    Last edited by Bad Wolf; 06 Apr 2018 at 18:27.
      My Computer


  10. Posts : 7,055
    Windows 7 Home Premium 32 bit
       #10

    I have in my post # 8 referenced this youtube video which lists the three possible causes Seagate backup plus portable Drive SRD00F1 ST1000LM035 100809471 repair data recovery - YouTube

    Most of the time it is the SATA to USB bridge that fails - from our experience.

    I do understand your reluctance to break open the case and take out the HDD for testing ( I won't do it if I consider my data so important that I wouldn't mind paying for a professional data recovery agency who are well equipped to do it). In that case it is best you entrust the work to Seagate Data Recovery partners.

    ( They are going to do the same thing. Unseal the case perhaps using a hot air chamber ( if it is a glue-sealed unit), try with another SATA to USB module first, if that doesn't resolve the problem, try changing the PCB which they may readily have in hand ( difficult/ near impossible to procure by the user), and if that fails, resort to data recovery procedures on the HDD itself.)

    In an on-line forum like this, we can do data recovery procedures only if the bare HDD is available for running the data recovery software and if it sees it.. Any other mechanical and electronics work, one would need physical possession of the external drive and more importantly necessary jigs/tools/spares for testing.

    "And how come my laptop is able to recognize the disk if there is a hardware problem, e.g. SATA to USB adapter?"

    A car that you couldn't start and run --- you still recognise it as a car, don't you? Reason out :)

    OK, I shall take you off any brain work. The SATA to USB bridge has many functions carried out by many chips either seperate or integrated. One part/function may fail.
    Last edited by jumanji; 08 Apr 2018 at 00:02.
      My Computer


 
Page 1 of 3 123 LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 05:11.
Find Us