Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: 2nd HDD gone after clone & boot from new drive

05 Sep 2018   #1
gb315

Windows 7 Home Premium 32bit
 
 
2nd HDD gone after clone & boot from new drive

I used Acronis True Image (WD edition) to clone my old HDD. For cloning, old_HDD was drive 0, new_HDD was drive 1. Before cloning, both drives were visible in Disk Manager. After cloning, I disabled drive 0 (old_HDD) in setup (F2). The system booted on drive 1 (new_HDD).

I next connected new_HDD as drive 0, and booted again. This too worked.

I then connected old_HDD as drive 1 and re-enabled it in Setup (F2). After booting, old_HDD/drive 1 is nowhere to be seen: Disk Manager just shows new_HDD/drive 0. I have re-booted a couple of times, with the same results.

Additional info:
- The drives are the same: WD5000 SATA
- I had a lot of trouble getting a bootable clone. I think this was because the current True Image WD edition "does not provide a booting feature" I 'succeeded' when using an old (2013?) version, running from a USB flash drive.




Attached Thumbnails
2nd HDD gone after clone & boot from new drive-diskmanager_screen.jpg  
My System SpecsSystem Spec
.
06 Sep 2018   #2
samuria

win 8 32 bit
 
 

Welcome to the forum. Do both drives show in the BIOS OK? If they don't show in BIOS it's either faulty cable,port or drive. If it shows in BIOS OK then ideally you need to boot a Linux free disk or acronis boot disk to see if they see the drive. If they see it OK delete partitions on the drive and reformat it should then show in Windows. Windows writes a signature to each disk so if you clone the drive you have two with the same signature so it gets confused at times and thinks it's the same disk as c. Did you try disk part to see if it sees it
My System SpecsSystem Spec
13 Sep 2018   #3
dsperber

Windows 7 Pro x64 (1), Win7 Pro X64 (2)
 
 

Never fails to amaze me when I hear these stories, as to why people continue to use Acronis when Macrium Reflect Free is available and is 100% reliable and NEVER causes this type of problem where the volume signature is improperly "duplicated" during the cloning process. Obviously this should NEVER be done, and the resulting problems are to be expected.

There's no comparison between the "understandable and completely intuitive" GUI of Macrium Reflect Free, and the [in my opinion] incomprehensible and off-putting GUI of Acronis (which I tried twice, and gave up twice, when I was investigating backup software). I can't understand how they're still in business.

Macrium Reflect Free FTW.
My System SpecsSystem Spec
.

Reply

 2nd HDD gone after clone & boot from new drive




Thread Tools




Similar help and support threads
Thread Forum
How do I get my new clone drive to act as boot?
Hi, Stuck for hours and hoping somebody can help. I'll try and make this as short and succinct as possible. Ty in advance if anyone can help direct me. I have three drives: 0. New 1tb SSD to replace my smaller drive 2. 1. 1tb HDD for data. 2. 250gb SSD for windows and programs.
General Discussion
Can't clone a new drive; can copy and rename drive letter work?
I recently bought a faster 2TB hard drive to replace my old 1TB 'games' hard drive. Unfortunately, the software that came with the drive (Seagate Disc Wizard) will not clone my 'games' hard drive onto the new hard drive. Every time I try the clone, the software tries to reboot the PC, thinking that...
Hardware & Devices
How to clone boot drive with read errors?
I can boot up ok. But the boot drive makes clicking sound sometimes and makes the computer slower, especially when waking up from a sleep. I tried using Acronis to clone the drive. It crashed as soon as the drive makes the first clicking sound and nothing is cloned. Since I can boot from the...
Installation & Setup
How to clone partition E: alone to boot from a new drive?
My current HDD holds: Primary NTFS Partition C: running XP. Logical NTFS Partition E: running Windows 7. Remains of a couple of Dell's recovery partitions primary FAT16 & FAT32. I would like to transfer only partition E: to a new SSD. And Keep the letter E: on the new drive, for it to work....
Installation & Setup
How can I clone an ide xp drive to dual boot on i5 laptop
Hi all, I hope I am in the correct forum. I have a Sony C series 64 bit laptop. I have a 2.5" IDE drive from my old laptop which has XP. I was thinking to image Win 7 on my Sony to a cd; so that I have a clean disk. How can I then clone my XP ide drive onto the new laptop drive - which is...
Installation & Setup


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 14:37.
Twitter Facebook Google+