After instaling windows 7 screen goes black an i cant do anything


  1. ferweks
    Posts : 6
    Windows Ultimate 32bit
       New #1

    After instaling windows 7 screen goes black an i cant do anything


    it's just like i've described into subject...
    I've installed windows 7 ulitimate 32bit and everything is went fine during installation.
    After last restart screen goes black and i cant do anything.I cant boot up into bios at all...The only thing that i get is the black screen and flickering bios cursor and only command that responding is ctrl+alt+del
    would you please help me on this problem!
    Thank you and sorry if my english is bad!
      My Computer
    Quote Quote

  3. TVeblen
    Posts : 6,292
    Windows 7 64 Bit Home Premium SP1
       New #2

    Hello ferweks. Welcome to the forum. Your English is fine.

    To get more intelligent answers, please fill out your "My System Specs" as thoroughly as you can.

    Is this a desktop or a laptop?
      My Computer
    Quote Quote

  4. ferweks
    Posts : 6
    Windows Ultimate 32bit
    Thread Starter
       New #3

    its a desktop computer.
    i have msi motherboard,2gb of ram (kingstone),nvidia 9600,seagate hdd...
      My Computer
    Quote Quote

  6. TVeblen
    Posts : 6,292
    Windows 7 64 Bit Home Premium SP1
       New #4

    Do you get a POST beep? A single beep that occurs within 5 seconds or so of pushing the power button and before the Bios screen starts.

    2 Things to try:

    Shut off the computer (Press and hold the power button for a few seconds, or you may have to use the power supply switch), wait a few minutes then power back on. Will the bios start now?

    Shut off the computer, disconnect the hard drive, then power back on. Will the bios start now?
      My Computer
    Quote Quote

  7. ferweks
    Posts : 6
    Windows Ultimate 32bit
    Thread Starter
       New #5

    i've tried what you propose to me...i've shot down and hold the power button for a few moments and nothing...
    but when im disconnected hard drive i've get message "Reboot and select proper boot device or insert boot media in selected boot device" and i put my windows 7 cd into cd rom and everything runs ok (it starting to install windows) i've tried again with conected hd and i get same thing...black screen and i can to nothing
    I didnt get my bios runing still and i didnt get beep sound on computers power on.
      My Computer
    Quote Quote

  8. TVeblen
    Posts : 6,292
    Windows 7 64 Bit Home Premium SP1
       New #6

    That is good. It tells us that you have working video and normal boot functions from CD/DVD.

    But I am confused because you normally do not get the "Reboot and select proper boot device or insert boot media in selected boot device" message until after the BIOS has started and run it's routine. Are you sure the BIOS does not POST or run?

    Try shutting down, restarting, and pressing the DEL key to enter the BIOS.

    If that doesn't work, you may need to do a Clear CMOS to get back into BIOS.

    • Shut down the computer > remove the power cord.
    • Remove the 3v battery.
    • Move the CLR CMOS jumper from pins 1-2 to 2-3.
    • Touch a metal part of the case and Press and Hold the reset button for approx. 30 seconds to discharge all power from the board.
    • Put the CLR CMOS jumper back on 1-2.
    • Replace the battery > replace the power cord > boot.
    • If the CLR CMOS worked you will need to reset the date and time.

    Also see here for BIOS troubleshooting on MSI boards:
    MSI Computer Corp. - Support
      My Computer
    Quote Quote

  10. ferweks
    Posts : 6
    Windows Ultimate 32bit
    Thread Starter
       New #7

    Yes im sure,it not post or run because i will start it by now,presing del or F12,F2,F8 and i cant do that at all,the only thing that i can do is ctrl+alt+del and it restarts computer.
    I will try to do this and i will let you know what i did!
    TVeblen,thanks for helping me,and thanks for your time!
      My Computer
    Quote Quote

  11. ferweks
    Posts : 6
    Windows Ultimate 32bit
    Thread Starter
       New #8

    i did what you told me,i reset clr cmos and i im entered into motherboard bios and i loaded optimized defalut settings,set up time and date and i save changes and exit and after all that i get same thing,black screen and i cant get into bios again...
      My Computer
    Quote Quote

  12. TVeblen
    Posts : 6,292
    Windows 7 64 Bit Home Premium SP1
       New #9

    Wow. This is confusing.
    You did a clear CMOS and got into the BIOS and could make changes. But when Saving & Exit it freezes. (That would be understandable if the W7 install was no good, and is a whole new issue), but if you then try and re-boot it won't POST or run the BIOS that would indicate a different issue.

    I'm wondering if the 3v CMOS battery could be dead (dying). Can you test the voltage on the battery? Or just replace it with a new one - they're pretty cheap.

    Also: keyboard & mouse. Are they wired or wireless?
      My Computer
    Quote Quote

  13. ferweks
    Posts : 6
    Windows Ultimate 32bit
    Thread Starter
       New #10

    ok i've think i've solved this one...im restarted bios by removing cmos once again, and im eneted into him and set up my boot devices,restarted my comp and im successfully start installation of Ubuntu...
    i've let you know if im was able to set up windows 7 after that!
    Thanks for your help and your time!
    All best!
      My Computer
    Quote Quote

 

  Related Discussions
Hi, I have this 4 year old Lenovo Y560(config below) The discrete graphic card has probably fried a long time ago, so last year when I did a clean install of Windows, I had to disable ATI Card permanently in the device manager using safe mode and used the Intel integrated card. A few days ago, I...
Hello, After doing a Windows update, my computer gave a Windows looking message that my hard drive was going bad and to back up my data. I was able to save my user files. Then the pc crashed with a BSOD. I disabled restart after crash. Found the error was 0x0000006B (having to do with a...
Whenever the Windows loadscreen passes the screen goes black and I can move a cursor around the screen. I have had this happen before and fixed it with bootrec.exe but I can't seem to get that to work this time... Startup repair says it cannot help - Safe mode has the exact same black screen...
Hi I would really appreciate any advice i've been trying to fix for four hours without any luck. I have an Acer aspire 5732Z. I turn my laptop on and it shows the starting windows screen then just goes to a black screen with a cursor. I tried to do systems restore but it said that i did not...
I am not sure what's wrong, but I have uninstall nvidia drivers that gave me problems ie. 257.21, 196.21....etc. I am currently using 195.62. I am certain that it was a VGA driver problem, because it never happened again, till I decided to remove windows internet explorer and it did the black...
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

 © Designer Media Ltd
All times are GMT -5. The time now is 22:18.
Find Us