Removing XP from dual-boot (not on same drive as 7)

Hi

Like the proverbial bad penny I'm back for more advice. This time my problem is that I have a PC which is dual boot with XP and I want to remove XP. Snag is they are on separate drives and the Mobo only gives me the option "Hard Drive" to boot from - NOT a choice of either of the two drives installed. I am therefore assuming it is imperative to get Win7 onto drive 1 - but how?

I've been going round in circles this afternoon trying to sort it out but everything I've tried has fallen to ashes and I've been struggling to get a working system. Thankfully I have four bootable CDs (Windows 7 Repair CD, Partition Wizard, Paragon Rescue Kit 11.0, Acronis TrueImage Home 2010 with Acronis Disk Director 10.0) that are specifically for times such as these and between them they have enabled me to get back to where I started, i.e. a dual-boot system with XP and Win7. So, where do I go from here?

Since I will be asked for a graphic of the disk management window I attach it here for your perusal. Incidentally, the Win7 partition on drive 1 is simply a copy of that in partition K: done using PW. At this stage it has only been copied with nothing whatsoever done with it - it is just a copy of K: which is on drive 2.

Tracey

Wolfgang, the problem is that Startup Repair will write the System boot files to the first marked-Active partition.

Additionally even if you would mark all preceding partitions INActive using Partition Wizard or Diskpart it will most often write to the first Primary partition on DISK0.

Hi All

Thanks for all the replies. As I've already said (and I thought this would be suggested) I have a multiplicity of different boot devices I can select BUT...only one hard disk. At present I assume this will always be disk 0. It has occurred to me that it would perhaps be an idea to remove the side from the PC and swap over the SATA connectors for the two drives. It would then be a case of making numerous changes to the partitioning so that I get the partitions in the order I want. I suspect though that this may take a lot of time. Still, not that it matters over much since it is only a spare PC and can be done as and when I have the time. Only thing is it could start getting a bit messy. I'd appreciate any comments on this if anyone cares to make any. Again, thanks for all the comments.

whs
No, Win7 was installed with both disks connected since as far as I knew at the time, XP was needed in order to instal Win7. I understand that since then a way of doing a clean install with an upgrade version has in fact been found. See above in reply to your comment re-boot order.

Tracey

Did you install Win7 to Disk 1 from XP, as it should be C and not K when you are booted into it if it was correctly installed from booted DVD?

If you don't care what drive letter it is now that you've run it that way for awhile, then easiest would be to mark K Active in Disk management, power down to unplug Disk0 and plug its cable into Disk1 making sure it remains set to boot first in BIOS, boot the Win7 DVD/Repair CD to run Startup Repair up to 3 separate times until Win7 starts on its own.

Afterwards plug back in the old XP HD to Disk1, use free Partition Wizard bootable CD to delete XP and repartition as you wish.

gregrocker

As far as I was aware at the time, I had to install Win7 with a qualifying OS installed. However, I believe it did give me the option of installing 7 to a different partition by doing a "Custom Install". Since I did not want to get rid of XP at that time I made space for 7 on drive 1 in partition K:

So what you are saying in your last post is to do the Startup Repair with the XP drive disconnected. OK, I now have to find out which is drive 0 and which is drive 1 but not too difficult. Will have a go at this today and let you know what happens. Before I do anything though I'll have to do some partition shuffling as there are programs that run at startup which are on my programs partition (I try my like hell to keep the Windows partition purely for Windows unless I'm given no choice).

Incidentally, on the previous thread I started (in the last week to ten days) a statement was made as follows:

Important:
When moving/resizing a partition which contains the Operating system (Windows 7) itself the BCD loader entry becomes invalid !! A "Windows Startup Repair" is the best solution in this case, so have your Windows 7 Repair CD ready.

Please tell me, is this right as I seem to remember resizing XP any number of times with no effect whatsoever on booting the PC - or does this just apply to Win7? Surely, if you're just resizing, the position of the boot files on the partition remain where they are so the pointers shouldn't need to be updated. If you move the partition then yes I can see how that MAY affect the booting process - but just resizing? (as you yourself have recommended many times with no mention of this problem!) I'd appreciate your comments.

Tracey