only have one...drive.one partition...
i did this
did you do this as well?
Bootsect /nt60 C: /mbr
Bootsect /nt60 C:
Bcdedit /store c:\boot\bcd /enum all
and this
diskpart
list disk (I assume disk 0 is you harddsik?)
sel disk 0
list part (how many partitions?)
sel part 1
det part
sel part 2
det part
sel part 3
det part
Bootsect /nt60 C: /mbr
Bootsect /nt60 C:
commands succeeded succesfully?
diskpart
sel disk 0
lis part (sure only 1 part?)
sel part 0 (or 1)
det part
is partition healthy? is it active? driveletter is C?
Bcdedit /store c:\boot\bcd /enum all
Do you see the lines I made bold?
Windows-opstartbeheer
---------------------
id {bootmgr}
device partition=C:
path \bootmgr
description Windows Boot Manager
locale nl-NL
inherit {globalsettings}
default {default}
resumeobject {fa1a7f9d-ab26-11df-bc4f-ce7145d50d35}
displayorder {default}
toolsdisplayorder {memdiag}
timeout 10
Windows-opstartlaadprogramma
----------------------------
id {default}
device partition=C:
path \Windows\system32\winload.exe
description Windows 7 Home Premium
locale nl-NL
inherit {bootloadersettings}
recoverysequence {fa1a7fa1-ab26-11df-bc4f-ce7145d50d35}
recoveryenabled Yes
osdevice partition=C:
systemroot \Windows
resumeobject {fa1a7f9d-ab26-11df-bc4f-ce7145d50d35}
nx OptIn
how can i make partition 1(drive letter C) as my active when i did list part command it says Primary onlyPartition### partition 1 ....tye...primary....size 233gb ....offset...150mb
just wondering Offtopic:
if i reformat my hard drive in toshiba it will erase my os right...also the bootloader or whatever it is right?
Last edited by noelian13; 10 Jan 2012 at 22:42.
i have the same of this in my command prompt
and i tried restarting booting from ehdd...run command prompt formatted drive C...proceed to install...then completing installation it restarted then still same error...its bsod...then....after it i tried bootrec /ScanOs and theres no total identified installations...since i guess its bcuz of the "completing installation" stage was nvr finished
and i tried rebuilding boot.ini ... nothing happens i queried
bootcfg /query and theres no boot.ini.... but win 7 was installed only boot.ini is not there o.0
sorry in advance
and tried system auto repair
at the end of details
root cause found
Failure while setup is in progress T_T
if in tutorial im stuck at this stage http://pcsupport.about.com/od/operat...l-part-2_3.htm
and start encountering bsod posted at the 1st post in my thread STOP: 0X0000007B
SOLVED: Well the people here with replies told me about the hdd not accessible so i got to bios..of toshiba..go to advance switched sata controller from ahci to comparability installed win 7....when in completing installation removed ehdd then worked....
Last edited by noelian13; 11 Jan 2012 at 03:44.
So you installed with C-drive in AHCI mode ... that should work. But when you change it to IDE mode in BIOS it can fix your problem. That is last thing I would advice you.
Because EVERYTHING is fine! bootmgr, bootmenu, MBR, bootsector. Stop 7B is an error you get when:
But your system is up and running now?
- moving the start point of a partition (with partition software)
- bios sata is in AHCI mode and win7 isn't or vice versa
Quote