Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.

Windows 7: I'm having wireless Issues with the Intel 1030,Turning off by itself

03 Apr 2013   #1

Windows 7 Professional
I'm having wireless Issues with the Intel 1030,Turning off by itself

I noticed my wireless 1030 is acting strange after getting BSOD(not the cause of Wireless but it was solved)and now I'm experiencing some problems, here are the issue. I'm worried if it is the NIC card it takes a while to connect to a certain webpage then whenI looked up on Event viewer it stated in the lines of Google too long to respond DNS

2. sometimes the wireless would switch off by itself and when I try to reconnect to my home router it says "Cannot find my router* yet I can see it shows my wireless router is available then when I look up event viewer it states " NETBIOS over TCPIP has entered Stop state".

I would have to click on

*Troubleshoot Problems which then would let me reconnect back in the router*

3. I have been getting this new event viewer error 5060:
The description for Event ID 5060 from source NETwNs64 cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.
If the event originated on another computer, the display information had to be saved with the event.
The following information was included with the event:
Intel(R) Centrino(R) Wireless-N 1030
I can see my network information by typing ipconfig/all BUT recently I performed a Intel® PROSet/Wireless Software Manual Diagnostics Tool and it failed on "Radio ON test" yet my wifi switch was ON. I'm really worried if it is the NIC card.
If it is the NIC card would I be able to replace it by not dismantling parts such as the keyboard/or screen to get to the card

My System SpecsSystem Spec
03 Apr 2013   #2

Windows 7 64-bit

It almost sounds like a nic driver issue. Have you updated it recently? Try to update, or roll-back if update did not work.
Replacing your nic should not be to hard depending on your device. Usually the nic is the easiest of the add-on boards to get to. But, I really don't think it's the nic. Were you changing, installing, updating anything with your hardware, operating system when this happened? If driver update/rollback doesn't work, try a system restore if feasible.
My System SpecsSystem Spec
05 Apr 2013   #3

Windows 7 Professional

Update: I noticed when my wireless connection turns off I get this message and I'm not sure what it means

"Router Advertisement settings have been changed on the network adapter 13. The current M - Managed Address Configuration flag is false and the O - Other Stateful Configuration flag is false. User Action: If you are seeing this event frequently, then it could be due to frequent change in M and O flag settings on the router in the network. Please contact your network administrator to have it resolved."
My System SpecsSystem Spec

06 Apr 2013   #4

Windows 7 64-bit

Hmm, these errors, I believe, are pointing towards an IPv6 issue. Do you have DHCPv6 disabled in your router? Unfortunately, I am a little clueless when it comes to the IPv6 stuff, other than my new router has it, is set to auto, and is configuring itself. My workstations are now getting v6 addresses. Hopefully someone else will chime in. Here is an article I found interesting. Understanding DHCPv6
My System SpecsSystem Spec
07 Apr 2013   #5

Windows 7 Ultimate x64

If you do not use IPv6 then disable it on your computer guide below:

How to disable IP version 6 or its specific components in Windows

Please post an ipconfig /all for review after it has been disabled.
My System SpecsSystem Spec

 I'm having wireless Issues with the Intel 1030,Turning off by itself

Thread Tools

Similar help and support threads
Thread Forum
Intel (R) Centrino (R) Wireless-N 1030 code 52 error
Hello, I sent my computer in for repairs a while back and now the wireless card won't work. It can't find any signals unless I plug in the one from my desktop. I went to computer/properties/device manager and saw that the wireless card (Intel (R) Centrino (R) Wireless-N 1030) has a yellow "!"...
Intel Centrino Wireless N 1000 Issues
Hello all, My friend is having trouble with her laptop. Specs: Lenovo Laptop Windows 7 Home Premium x64 8.0 GB RAM 500 GB HDD Intel Centrino Wireless N 1000
Hardware & Devices
Intel Centrino Wireless-N 1030, CMD prompt question
This card supports 802.11n. Obviously... it's right in the name, plus device manager>network adapters>Intel Centrino>Advanced tab clearly shows n enabled. But can anyone take a second to tell me, if you know, why when I run the command netsh wlan show drivers, "radio types supported" shows only...
Hardware & Devices
PCI-E intel 5300 wireless doesn't work. Then the USB wireless adapter
Dear all, I thought I have met this problem before before my two wireless adapters both stopped working. PCI-E INTEL 5300 TP-LINK WN821N My case is a little different from those I found on this forum. 1. When I upgraded my thinkpad x200 to win7 64bit, I don't have "Wireless Network...
Network & Sharing
Turning v-sync off with an Intel laptop?
Hey, so.. This might sound a litle newbie but this problem is really annoying and I really wanna fix it. So I installed Win 7 and I was all happy, fresh stuff and all. Well the problem was when I started playing games and the fps dropped to 60. I know my laptop is not that good but I know it can...
General Discussion

Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd

All times are GMT -5. The time now is 07:35.
Twitter Facebook Google+