Gigabit LAN Connection Speed Problem


  1. tmetford
    Posts : 3
    Windows 7 Professional x64
       New #1

    Gigabit LAN Connection Speed Problem


    Most times, after my PC has booted, the Local Area Connection Status dialogue box shows a connection speed of only 100Mbps instead of the 1Gbps that it is designed to run at.
    My PC does occasionally connect at 1Gbps on a cold boot, usually after I’ve run a registry optimisation programme.
    This shows me that it is actually capable of running at 1Gbps but, usually upon a reboot, it defaults to 1Mbps again.
    It also, occasionally and spontaneously, changes its connection speed from 100Mbps to 1Gbps upon Resume from Sleep mode. (i.e. say after a cold boot it runs at 100Mbps (as per usual), if I then put it into Sleep Mode for a while and wake it up again, it sometimes resumes showing a connection speed of 1Gbps!
    I have carried out all the checks/BIOS upgrades suggested by Gigabyte for my motherboard with no change. I have replaced the Ethernet cable with a new (CAT5E) cable that I know supports 1Gbps connection speeds.
    I use a Netgear GS108 8-port Gigabit Switch on my LAN which shows me when my LAN connection is running at 1Gbps (green LED) and when it’s running at 100Mbps (orange LED). I observe that, during a cold boot the LED flashes green 5 or 6 times and then defaults to a steady orange colour (i.e. 100Mbps), by which time the Log In screen has appeared. It’s as if the system attempts to load the gigabit driver which fails and so it resorts to the 100Mbps driver?
    I think this may be a driver issue but I don’t know how to tackle it.
    My PC's network card driver details: Atheros AR8131 PCI-E Gigabit Ethernet Controller (NDIS 6.20)
    Any ideas will be gratefully received.
    Thank you for reading all this through!
    Tim.
      My Computer
    Quote Quote

  3. fireberd
    Posts : 8,135
    Windows 10 64 bit
       New #2

    Do you have more than one NIC (Ethernet) on your motherboard? My Gigabyte motherboard has two, an Intel and Atheros 8151. If yours has more than one, try the other and see what happens.

    As you have a switch, between your PC and the modem, can you connect directly to the modem - at least for testing to see how it reacts connected directly to the modem.

    Registry "optimization", cleaners, PC speed ups, repairers, or whatever they are called can cause more problems than they claim to fix or speed up. NEVER use one and especially in Windows 7 and Windows 8. Most "techies" consider them in the "snake oil" category. I do PC repair and I've had to fix several clients PC's after running these so called registry programs. Even the one with Ccleaner.
      My Computer
    Quote Quote

  4. tmetford
    Posts : 3
    Windows 7 Professional x64
    Thread Starter
       New #3

    Hi Fireberd and thanks for your suggestions.
    Unfortunately my motherboard has only one NIC socket and, as for connecting directly to my router/modem, there's no difference there either which is a shame - nice idea though!
    I've used Iolo's System Mechanic on all my PCs and Laptops for the past decade (l've caused too many screw-ups in the past, so I leave the OS alone now except for reviewing the list of services and disabling those that I know I can get rid of).
    System Mechanic seems to have worked very well with Windows XP and I'd never have suspected that it might (if it's like other reg optimising software), create some problems with Windows 7. In its defence I've found System Mechanic to have a number of redeeming features, such as easily turning off unwanted background processes and start up software. However I've not yet tried Win 7 without it so this may be worth a shot when I next do a complete re-install on my PC.

    I wondered if, when a PC boots, the sequence in which the various drivers are loaded into memory may make a difference?
    Is it worth attempting to re-order this boot sequence? or would I be on a hiding to nothing?

    Thanks once again.
    Tim
      My Computer
    Quote Quote

  6. fireberd
    Posts : 8,135
    Windows 10 64 bit
       New #4

    XP did not manage the Registry very well. However, its different in Win7/Win8, what they "fix" is very questionable. There are some interesting posts on here about why not to use them with Win7/8.

    I have "Win Patrol" and it does the management, monitoring, etc. Many "techies" have this program. BillP Studios Download Page

    What you can do, to see if helps, is to uninstall the NIC in the Device Manager. Then restart the PC and when Windows starts it will detect and reinstall it. This can put it in a different initialization point and may even put it on a different shared IRQ that may make a difference.

    The saving part is that it doesn't matter if its operating at 100Mb/sec or 1Gigabyte/sec, your internet speed is no where either one's speed.

    Here is a current Windows 7 forum thread on the Registry Cleaners. Basically says what I have said.
    Registry cleanup
      My Computer
    Quote Quote

  7. tmetford
    Posts : 3
    Windows 7 Professional x64
    Thread Starter
       New #5

    That's great, thanks for the links and advice: duly noted.
    Next time I do a clean installation I'll leave the registry well alone - you never know, my computer might work better!
    Thank you
    Regards
    Tim
      My Computer
    Quote Quote

 

  Related Discussions
Can't get gigabit speed in Win7
in Network & Sharing

I have a GA-X58A-UD3R motherboard connected to a netgear gigabit switch. When I boot into Ubuntu 14.04 the switch light turns green. In windows 7 it's yellow and looking into network connections it says 100 megs not 1000. I think it used to be green before I installed Oracle Virtual box but I'm...
Gigabit port speed
in Network & Sharing

Hi all, I have a 100/25 Mbps fiber optic connection with a Technicolor TG784n v3 router and I'm having problems with the speed on the Gigabit port. When I turn the computer off or restart it the speed drops to 50 Mbps. If I connect the PC to one of the other 100 Mbps ports the speed returns to...
Gigabit Network Speed Question
in Network & Sharing

I have a desktop workstation with an intel xeon 2.53ghz and 4gb of ddr3 ram, it has a broadcom netxtreme 57xx gigabit controller, and i have an Iomega home media drive, also a gigabit switch. I have my computer connected to the switch and the NAS to the switch as well, all using CAT6 cable....
ello folks a friend of mine now has a gigabit connection but can only get 400Mb download when tested via speedtest.net. while the engineer was installing everything he noted speeds of 700Mb on the laptop used for the setup. could any of you suggest how he would go about getting better speeds?...
Home gigabit LAN speed problem
in Network & Sharing

Hi guys, I have 3 Win7 PC's in a network connected with some D-Link gigabit router and all PC's have gigabit ethernet cards. They all have IP addresses entered and subnet masks. The speed before was great, around 50MB/s. Now one of the PC's has a slower speed. It's now only around 10MB/s when...
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

 © Designer Media Ltd
All times are GMT -5. The time now is 22:58.
Find Us