Ping DG, ftp block/httpd block


  1. Posts : 302
    Windows 8 64bit Professional
       #1

    Ping DG, ftp block/httpd block


    Hello Guys,


    I find this to be quite embarrassing, having an issue like this that I can't figure out.

    Here's what I can't do.

    1. Ping DG (Default Gateway)
    2. Ping my IP (96.46.29.108)
    3. Can't access my router via remote, even though its setup to allow it.

    What I can do.

    1. Access any web page.
    2. Ping any website but my own IP/DG.
    3. Play games & use the internet like usual.

    I've forwarded the ports I use, and allowed all the programs to roll through the Firewall without issues. I'm not sure if my ICMP was disabled on my router, my family currently shut down my computer, so I can't remote in, and work on it.

    I installed TeamViewer because LogMeIn isn't going to accept any "Free" connections anymore, and will require a paid subscription. I've got an older version of RealVNC installed, but I couldn't remember my serial key.


    Sincerely,
    Thomas
      My Computer


  2. Posts : 2,298
    Windows 7 Professional x64 SP1 ; Windows Server 2012 R2 Standard
       #2

    Is this from a remote location or from within the local LAN of the router? If remote, when you mean Default Gateway, is that the remote router you are trying to access or the default gateway used to access the internet?

    Have you checked that the public IP address is current? Unless you have paid for a static IP address it is very possible for a different one to be assigned via DHCP by the ISP.

    Josh :)
      My Computer


  3. Posts : 302
    Windows 8 64bit Professional
    Thread Starter
       #3

    Shadowjk said:
    Is this from a remote location or from within the local LAN of the router? If remote, when you mean Default Gateway, is that the remote router you are trying to access or the default gateway used to access the internet?

    Have you checked that the public IP address is current? Unless you have paid for a static IP address it is very possible for a different one to be assigned via DHCP by the ISP.

    Josh :)
    Thanks for the reply, Josh.

    I've done remote, and from within the network. I can ping my local IP, but not my public address. I'm trying to remote access my router via https, and it fails it. Doesn't matter which IP Address I use.


    My IP Address shouldn't have changed at all. It's been the same for a few years now. I'll check into that theory though. The IP Address that goes to the router is a static IP, and then gives the IPs out via DHCP.
      My Computer


  4. Posts : 457
    Microsoft Windows 10 Home Build 15036
       #4

    DreadStarX said:

    Thanks for the reply, Josh.

    I've done remote, and from within the network. I can ping my local IP, but not my public address. I'm trying to remote access my router via https, and it fails it. Doesn't matter which IP Address I use.


    My IP Address shouldn't have changed at all. It's been the same for a few years now. I'll check into that theory though. The IP Address that goes to the router is a static IP, and then gives the IPs out via DHCP.
    Can you do a WHOIS on yourself? What I'm asking is, is there any internet protocol function working that you can direct back at yourself.

    Have you asked anyone else to try and ping your (public) IP addy from their own computer and network?

    I think the question that was asked was in reference to your public addy. Your internet provider gave your router the address and that can change from one boot to the next. Internally, I'm at 192.168.1.10, and my router is 192.168.1.1. Externally, my router is 92.xxx.254.17.
      My Computer


  5. Posts : 2,298
    Windows 7 Professional x64 SP1 ; Windows Server 2012 R2 Standard
       #5

    DreadStarX said:
    Shadowjk said:
    Is this from a remote location or from within the local LAN of the router? If remote, when you mean Default Gateway, is that the remote router you are trying to access or the default gateway used to access the internet?

    Have you checked that the public IP address is current? Unless you have paid for a static IP address it is very possible for a different one to be assigned via DHCP by the ISP.

    Josh :)
    Thanks for the reply, Josh.

    I've done remote, and from within the network. I can ping my local IP, but not my public address. I'm trying to remote access my router via https, and it fails it. Doesn't matter which IP Address I use.


    My IP Address shouldn't have changed at all. It's been the same for a few years now. I'll check into that theory though. The IP Address that goes to the router is a static IP, and then gives the IPs out via DHCP.
    My apologies if I wasn't clear, Yes your router acts as a DHCP server for the 192.168.1.0/24 network or of a similar private IP address setup. When remote connecting you will be remotely connecting using a publicly assigned IP address that was given to you by your ISP (96.46.29.108). This is set by DHCP with your ISP acting as the server and your router's internet connection being the client side. Overtime this can change since the ISP will re-use their public IP addresses to ensure scalability. Why set a static IP address to a customer who's router is turned off?

    As PeaB4YouGo suggests, trying to ping 192.168.1.X will fail if you attempt to do that remotely since that is a private IP address and is not routed on the internet. I did attempt to send a ping to your public IP address to see if a connection from me worked, however I received a request timed out. This could be a block placed by your ISP or the address not currently being used.

    I do know that some routers are set-up to NOT respond to ping or allow remote access from the internet to the config page for security reasons. One of the most secure set-up is one where a malicious actor is not able to enter in a username or password at all.

    Ping DG, ftp block/httpd block-capture.png

    Double check the router settings and see if the IP address is the same. Unless you have explicitly paid for it the address may have changed.

    Josh :)
      My Computer


  6. Posts : 302
    Windows 8 64bit Professional
    Thread Starter
       #6

    Hey Guys,


    I can ping my LAN Address (192.168.1.106), and I'm fine. I've pinged my computer from my work PC (This one I'm on), and I get a Timed Out Message.


    I've gone ahead and released my ip address, and I'll renew it when my family gets home from work. I think I've had this IP too long and things are messing up.


    My brothers computer has the same IP Address as mine, 96.46.29.108, this is from whatismyip.com & ipchicken.com.

    I have no idea what in the heck is going on, and I'm starting to get frustrated.
      My Computer


  7. Posts : 2,298
    Windows 7 Professional x64 SP1 ; Windows Server 2012 R2 Standard
       #7

    NAT is the problem. 192.168.0.0/16; 172.16.0.0/12; 10.0.0.0/8 are all private IP addresses and cannot be routed on the internet. To resolve this, when your internal LAN devices access the internet their source IP address is translated to the one public IP address configured on your WAN interface connecting to the internet. This translation is done on a layer 4 (TCP/UDP ... etc) port basis so two devices can be seen as having the same public IP address to the internet.

    I take it your work PC is remote from your LAN? You cannot ping a private IP address remotely. It just doesn't work since they are not routed on the internet. Chances are your works network has it set to drop any traffic destined to a private IP address that does not exist rather than sending the traffic to the ISP (via the Default Route) and having the ISP drop it since it is a private IP address.

    The issue with NAT is that it is a one way system (More of a benefit in the context of security). You cannot send data to a device without it first initiating the session. From your internal LAN you can ping google but google can't ping you unless you started the connection.

    Hope This Helps,
    Josh :)
      My Computer


  8. Posts : 302
    Windows 8 64bit Professional
    Thread Starter
       #8

    Shadowjk said:
    NAT is the problem. 192.168.0.0/16; 172.16.0.0/12; 10.0.0.0/8 are all private IP addresses and cannot be routed on the internet. To resolve this, when your internal LAN devices access the internet their source IP address is translated to the one public IP address configured on your WAN interface connecting to the internet. This translation is done on a layer 4 (TCP/UDP ... etc) port basis so two devices can be seen as having the same public IP address to the internet.

    I take it your work PC is remote from your LAN? You cannot ping a private IP address remotely. It just doesn't work since they are not routed on the internet. Chances are your works network has it set to drop any traffic destined to a private IP address that does not exist rather than sending the traffic to the ISP (via the Default Route) and having the ISP drop it since it is a private IP address.

    The issue with NAT is that it is a one way system (More of a benefit in the context of security). You cannot send data to a device without it first initiating the session. From your internal LAN you can ping google but google can't ping you unless you started the connection.

    Hope This Helps,
    Josh :)
    It didn't use to be this way. I used to be able to host an ftp/mysql/webserver on my desktop at home. It wasn't until we switched companies (Company A was bought by Company B), and we were forced to switch. =/ I guess I'll give them a call.
      My Computer


  9. Posts : 2,298
    Windows 7 Professional x64 SP1 ; Windows Server 2012 R2 Standard
       #9

    DreadStarX said:
    Shadowjk said:
    NAT is the problem. 192.168.0.0/16; 172.16.0.0/12; 10.0.0.0/8 are all private IP addresses and cannot be routed on the internet. To resolve this, when your internal LAN devices access the internet their source IP address is translated to the one public IP address configured on your WAN interface connecting to the internet. This translation is done on a layer 4 (TCP/UDP ... etc) port basis so two devices can be seen as having the same public IP address to the internet.

    I take it your work PC is remote from your LAN? You cannot ping a private IP address remotely. It just doesn't work since they are not routed on the internet. Chances are your works network has it set to drop any traffic destined to a private IP address that does not exist rather than sending the traffic to the ISP (via the Default Route) and having the ISP drop it since it is a private IP address.

    The issue with NAT is that it is a one way system (More of a benefit in the context of security). You cannot send data to a device without it first initiating the session. From your internal LAN you can ping google but google can't ping you unless you started the connection.

    Hope This Helps,
    Josh :)
    It didn't use to be this way. I used to be able to host an ftp/mysql/webserver on my desktop at home. It wasn't until we switched companies (Company A was bought by Company B), and we were forced to switch. =/ I guess I'll give them a call.
    So is this an issue with connecting to the router or the the computer hosting the data? Your original post didn't make it clear that you were actually hosting something but rather couldn't access your router...

    This might be why there's confusion with addressing.

    It might be worth seeing if the ports you use are blocked by your ISP since hosting websites and services normally require a business package or subscription of some sort. As a testing measure, try to place your hosted server into the DMZ zone on your router. This will open up all ports and help to verify if this is a port based issue. If that works then you can remove the server from the DMZ and troubleshoot your port forwarding. If it doesn't then I would check that your public IP address on the router is the same as what you were trying to access and that your ISP isn't blocking the ports themselves.

       Warning
    Remember to remove the server from the DMZ zone after testing since it may be vulnerable to attack.


    Josh :)
      My Computer


  10. Posts : 302
    Windows 8 64bit Professional
    Thread Starter
       #10

    I fixed the pinging problem. Now I've got to figure out where I went wrong with the FTP/Webserver.

    Thanks guys!

    It was "Block Anonymous Incoming Requests".
      My Computer


 

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 22:03.
Find Us