New
#1
Overclock Settings - Help To Tighten Up
Here are my overclock settings. I just ran a LinX stress test for 8 hours without a problem. My temps did reach 77C, but then again, the temps inside my house reached over 80F today. I was hoping that someone could help me tighten them up a little. I know I'm not using my memory or processor to their full extent, that's where you come in. If you could, please look over the settings and if you see a change or two (or three) that could help, feel free to send it my way. Thanks!!
CPU Clock Ratio [21x]
CPU Frequency: 3.78GHz (180x21)
Advanced CPU Features [Press Enter]:
CPU Clock Ratio [21x]
CPU Frequency: 3.78GHz (180x21)
Intel(R) Turbo Boost Tech [Enabled]
CPU Cores Enabled [All]
CPU Multi-Threading [Enabled]
CPU Enhanced Halt (C1E) [Disabled]
C3/C6/C7 State Support [Enabled
CPU Thermal Monitor [Enabled]
CPU EIST Function [Enabled]
Virtualization Technology [Enabled]
Bi-Directional PROCHOT [Enabled]
Virtualization Technology [Enabled]
QPI Link Ratio [x36]
QPI Link Speed [6.48GHz]
Uncore & QPI Features [Press Enter]:
QPI Clock Ratio [x36]
QPI Link Speed: 6.48GHz
Uncore Clock Ratio [x17]
Uncore Frequency 3060MHz
Isonchronous Frequency [Enabled]
Base Clock (BCLK) Control [Enabled]
BCLK Frequency (MHz) [180]
Advanced Clock Control [Press Enter]:
>>>>> Standard Clock Control
Base Clock (BCLK) Control [Enabled]
BCLK Frequency (MHz) [180]
PCI Express Frequency (MHz) [100]
C.I.A.2 [Disabled]
>>>>> Advanced Clock Control
CPU Clock Drive [ 800mV]
PCI Express Clock Drive [ 900mV]
CPU Clock Skew [ 0ps]
IOH Clock Skew [ 0ps]
Performance Enhance [Standard]
Extreme Memory Profile (X.M.P.) [Disable]
System Memory Multiplier (SPD) [8.0]
Memory Frequency (MHz) 1066 1440
DRAM Timing Selectable (SPD) [Auto]
Profile DDR Voltage 1.5V
Profile QPI Voltage 1.175V
Channel A
CAS Latency Time 8 [Auto]
tRCD 8 [Auto]
tRP 8 [Auto]
tRAS 20 [Auto]
Command Rate (CMD) 2 [Auto]
Channel B
CAS Latency Time 8 [Auto]
tRCD 8 [Auto]
tRP 8 [Auto]
tRAS 20 [Auto]
Command Rate (CMD) 2 [Auto]
Channel C
CAS Latency Time 9 [Auto]
tRCD - [Auto]
tRP - [Auto]
tRAS - [Auto]
Command Rate (CMD) - [Auto]
Advanced DRAM Features [Press Enter]:
Performance Enhance [Standard]
Extreme Memory Profile (X.M.P.) [Disable]
System Memory Multiplier (SPD) [8.0]
Memory Frequency (MHz) 1066 1440
DRAM Timing Selectable (SPD) [Auto]
Profile DDR Voltage 1.5V
Profile QPI Voltage 1.175V
x Channel Interleaving 6 Auto
x Rank Interleaving 4 Auto
>>>>> Channel A
Channel A Timing Settings [Press Enter]:
>>>>> Channel A Standard Timing Control
x CAS Latency Time 8 Auto
tRCD 8 Auto
tRP 8 Auto
tRAS 20 Auto
>>>>> Channel A Advanced Timing Control
x tRC 27 Auto
x tRRD 4 Auto
x tWTR 4 Auto
x tWR 8 Auto
x tWTP 19 Auto
x tWL 7 Auto
x tRFC 60 Auto
x tRTP 4 Auto
x tFAW 20 Auto
x Command Rate (CMD) 2 Auto
>>>>> Channel A Misc Timing Control
x B2B CAS Delay - Auto
x Round Trip Latency 67 Auto
>>>>> Channel A
Channel A Turnaround Settings [Press Enter]:
>>>>> Channel A Writes Followed by Reads
x Different DIMMs 6 Auto
x Different Ranks 6 Auto
x On The Same Rank 6 Auto
>>>>> Channel A Reads Followed by Writes
x Different DIMMs 8 Auto
x Different Ranks 8 Auto
x On The Same Rank 8 Auto
>>>>> Channel A Reads Followed by Reads
x Different DIMMs 6 Auto
x Different Ranks 5 Auto
x On The Same Rank 1 Auto
>>>>> Channel A Writes Followed by Writes
x Different DIMMs 6 Auto
x Different Ranks 6 Auto
x On The Same Rank 1 Auto
>>>>> Channel B
Channel B Timing Settings [Press Enter]:
>>>>> Channel B Standard Timing Control
x CAS Latency Time 8 Auto
tRCD 8 Auto
tRP 8 Auto
tRAS 20 Auto
>>>>> Channel B Advanced Timing Control
x tRC 27 Auto
x tRRD 4 Auto
x tWTR 4 Auto
x tWR 8 Auto
x tWTP 19 Auto
x tWL 7 Auto
x tRFC 60 Auto
x tRTP 4 Auto
x tFAW 20 Auto
x Command Rate (CMD) 2 Auto
>>>>> Channel B Misc Timing Control
x B2B CAS Delay - Auto
x Round Trip Latency 69 Auto
>>>>> Channel B
Channel B Turnaround Settings [Press Enter]:
>>>>> Channel B Writes Followed by Reads
x Different DIMMs 6 Auto
x Different Ranks 6 Auto
x On The Same Rank 6 Auto
>>>>> Channel B Reads Followed by Writes
x Different DIMMs 8 Auto
x Different Ranks 8 Auto
x On The Same Rank 8 Auto
>>>>> Channel B Reads Followed by Reads
x Different DIMMs 6 Auto
x Different Ranks 5 Auto
x On The Same Rank 1 Auto
>>>>> Channel B Writes Followed by Writes
x Different DIMMs 6 Auto
x Different Ranks 6 Auto
x On The Same Rank 1 Auto
>>>>> Channel C
Channel C Timing Settings [Press Enter]:
>>>>> Channel C Standard Timing Control
x CAS Latency Time 8 Auto
tRCD 8 Auto
tRP 8 Auto
tRAS 20 Auto
>>>>> Channel C Advanced Timing Control
x tRC 27 Auto
x tRRD 4 Auto
x tWTR 4 Auto
x tWR 8 Auto
x tWTP 19 Auto
x tWL 7 Auto
x tRFC 60 Auto
x tRTP 4 Auto
x tFAW 20 Auto
x Command Rate (CMD) 2 Auto
>>>>> Channel C Misc Timing Control
x B2B CAS Delay - Auto
x Round Trip Latency 70 Auto
>>>>> Channel C
Channel C Turnaround Settings [Press Enter]:
>>>>> Channel C Writes Followed by Reads
x Different DIMMs 6 Auto
x Different Ranks 6 Auto
x On The Same Rank 6 Auto
>>>>> Channel C Reads Followed by Writes
x Different DIMMs 8 Auto
x Different Ranks 8 Auto
x On The Same Rank 8 Auto
>>>>> Channel C Reads Followed by Reads
x Different DIMMs 6 Auto
x Different Ranks 5 Auto
x On The Same Rank 1 Auto
>>>>> Channel C Writes Followed by Writes
x Different DIMMs 6 Auto
x Different Ranks 6 Auto
x On The Same Rank 1 Auto
Load Line Calibration [Disabled]
CPU Vcore 1.13125v [1.25000v]
QPI/VTT Voltage 1.175v [1.295v]
IOH Core 1.100v [Auto]
DRAM Voltage 1.500v [1.640V]
Advanced Voltage Control [Press Enter]:
Load Line Calibration [Disabled]
CPU Vcore 1.13125v [1.27500v]
x Dynamic Vcore (DVID) +0.00000V Auto
QPI/VTT Voltage 1.175v [1.295v]
CPU PLL 1.800v [1.800V]
>>> MCH/ICH
PCIE 1.500v [Auto]
QPI PLL 1.100v [Auto]
IOH Core 1.100v [Auto]
ICH I/O 1.500v [Auto]
ICH Core 1.100v [Auto]
>>> DRAM
DRAM Voltage 1.500v [1.640V]
DRAM Termination 0.750v [Auto]
Ch-A Data VRef. 0.750v [Auto]
Ch-B Data VRef. 0.750v [Auto]
Ch-C Data VRef. 0.750v [Auto]
Ch-A Address VRef. 0.750v [Auto]
Ch-B Address VRef. 0.750v [Auto]
Ch-C Address VRef. 0.750v [Auto]