Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Post Your Overclock!

18 May 2012   #1781
smarteyeball

 
 

Quote   Quote: Originally Posted by Wishmaster View Post


I haven't researched much into IB, but do they run warmer than Sandy chips do?
Yep

When I built this rig, I opted for the 2500K as a 'temporary' chip until IVY was released, but with the current heat issues and great performance as is - I might end up skipping IVY unless they do a revision.


Lately I've ignored my own advice and have been playing with the BCLK. 102.5 pushes me up to 4.726ghz and my 2133mhz modules seem quite happy @ 2190mhz.

They seem to have mhz headroom, but hate having the timings adjusted


My System SpecsSystem Spec
.
18 May 2012   #1782
Britton30
Microsoft MVP

Windows 7 Ultimate X64 SP1
 
 

Hi Patrick, where ya been?
I suspect the higher RAM frequency will make up for a bit looser timing?
My System SpecsSystem Spec
18 May 2012   #1783
Wishmaster

Windows 7 Home Premium 64bit
 
 

From my limited experiences, most Intel chips seem to like more Bandwidth over tighter Timings anyway, so I wouldn't even worry about it.
2190Mhz is pretty fast
My System SpecsSystem Spec
.

19 May 2012   #1784
smarteyeball

 
 

Quote   Quote: Originally Posted by Britton30 View Post
Hi Patrick, where ya been?
I suspect the higher RAM frequency will make up for a bit looser timing?
I've been around

I just took a break from fiddling.

Raw mhz has definitely more impact than tighter timings.

Quote   Quote: Originally Posted by Wishmaster View Post
From my limited experiences, most Intel chips seem to like more Bandwidth over tighter Timings anyway, so I wouldn't even worry about it.
2190Mhz is pretty fast
yeah, I've given up on timing tightening - There's no pay off. Raw mhz gives better bandwidth and lower latency.

I'm testing a bclk of 103.1 which is giving me 2200MHZ. I was running the DRAM at 1.62500 and VCCIO at 1.125 and got an idle BSOD at 2090Mz.

I've now upped the dram to 1.65 / 1.15 and adjusted the - offest a few notches. I might give it a proper stress later to see how it's affecting the PIC-E lanes (GPU) etc.

These are some 'realworld temps' atm (converting video) -.030 iirc

Post Your Overclock!-converting.jpg

Post Your Overclock!-2200mhz.jpg


EDIT:

Nope - It did not like running that quick. BSOD. Time to dial and fiddle...


My System SpecsSystem Spec
19 May 2012   #1785
smarteyeball

 
 

*Sigh* back to the drawing board.

Edit:

Decided to start low, test properly and then increase as need be.

BCLK 102.5 / 4.695ghz / 2176mhz /-0.020 offset /1.65v DRAm and 1.5 VCCIO / CPU spectrum Enabled / LLC set to medium (%25)

10 pas of IBT maximum. Now priming.

If that is stable, then I'll do what I normally do -lower settings, don't bother 'stress testing' and cross fingers with real world usage

And if it fails Prime95 - I'll swear. Basically the tried and true method of overclocking

I'm getting the same bandwidth/latency @ 2175mhz that I was at 2200mz, give or take the odd Mb and .X ns

29K winsat and 43ns is quick in any mans language
My System SpecsSystem Spec
19 May 2012   #1786
Dave76

Microsoft Community Contributor Award Recipient

Windows 7 Ult x64 - SP1/ Windows 8 Pro x64
 
 

Nice OC, no swearing?
My System SpecsSystem Spec
19 May 2012   #1787
smarteyeball

 
 

No, there has been several bouts of swearing since then :P

P95 failure about an hour in. BSOD the next run. etc

Good old 'pass Ibt', yet fail Prime.

I'm dropping the BCLK each time. Now I'm trying using a + offset. I suspect there will be more swearing before the night is through.

I probably should be doing a memtest run but god damn that test bores me to tears...


One thing that's always had me curious about overclocking is:

"Rig has a decent and stable OC and all is fine". Then out of the blue it's suddenly not acceptable and things must be tinkered with to the point of frustration and the sometimes inevitable rollback to original stable overclock
My System SpecsSystem Spec
19 May 2012   #1788
Britton30
Microsoft MVP

Windows 7 Ultimate X64 SP1
 
 

Computers are cranky. I've come back to a BSOD after a night's sleep...after a high pass with IBT.
My System SpecsSystem Spec
19 May 2012   #1789
smarteyeball

 
 

Quote   Quote: Originally Posted by Britton30 View Post
Computers are cranky. I've come back to a BSOD after a night's sleep...after a high pass with IBT.
Those are the absolute worst Dejection is the main emotion with frustration and annoyance mixed in.

I know the feeling all to well

I'm currently a couple of hours into a 4.75ghz / BCLK 101.1 / 2156Mhz / No LLC / + 0.010 offfset(?) + a few different tweaks and 'so far so good.

IBT max 10 didn't go above 70c and vcore topped at 1.308

Priming atm @ 1.288v with 59c across all cores.

I've been swear free for a few hours now

So far It's still quite an acceptable vcore for the clock speed with plenty of headroom.

I think this latest bout of tweaking is down to preparing for any potential SLI GTX 670 bottleneck eradication.
My System SpecsSystem Spec
19 May 2012   #1790
Britton30
Microsoft MVP

Windows 7 Ultimate X64 SP1
 
 

Keep the world swear-free and enjoy. Why are we moved to fiddle-fart around with a stable system to "see if this works"?
1.288V is darned good for 4.75GHz, I can't seem to get mine to run more than 4.5.
My System SpecsSystem Spec
Closed Thread

 Post Your Overclock!




Thread Tools




Similar help and support threads
Thread Forum
Post Your Overclock! [2]
Continued from - https://www.sevenforums.com/overclocking-case-mods/2309-post-your-overclock.html Finally hit 5GHz on air!
PC Custom Builds and Overclocking
Should I overclock my CPU?
Hello all, Recently my temps of my CPU have gone out of control, however, I disabled turbo mode in my bios and it works much better. Temps are less than 70c under full load My question is should I overclock this CPU I have? specs: CPU: Intel core i5 650 3.20GHz Mobo: Intel dq57tm
PC Custom Builds and Overclocking
odd post/bios screen, plus no keyboard detected @ post
i had recently built a new computer. after installing windows 7 everything was fine, except for during start-up it'd say 'no keyboard deteced'. which it wasn't detecting it because i couldnt acess bios during this. once i came to the windows log in screen, it was then reading the keyboard. a...
General Discussion
Cant seem to get an overclock
Hi have an i7 2700k and an Asus P8H 61-M LE usb3 mobo and when i do a autotune overclock it says 4.0ghz and should set in the bios but it dosent,could anyone help me out on this one please Thanks
PC Custom Builds and Overclocking


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 02:48.
Twitter Facebook Google+ Seven Forums iOS App Seven Forums Android App