OC Help

N00berG00ber said:

OK, I've tried with stock settings and bios and it was fine. But I only ran it for a few mins. Only got to test 5 in prime before I stopped it.

Start it and let it go for an hour and see what happens otherwise you can not really call it a real stress test. And will not have any weight anywhere as evidence of a Mobo issue.

So prime this time just froze on me. It dident shut down my computer. I'm at 1.488v 4.y and running Intel maximum. Considering I was able to go through 13 prime tests on my last mono with the same speed and voltage, I think its this board.

N00berG00ber said:

Solarstarshines said:

N00berG00ber said:

Intel very high test got to 1 test done. hen I stopped it. I tried maximum and it never even got through 1 test and froze. 4.6 at 1.476v

there is something wrong do you have any power states disabled ?

I disabled everything.

I've tried with c6 enabled and disabled. Dosent make a difference.

I'm flashing and older bios version now.....

I personally think the board is messed up. i think i see a long very angry talk with asus tomorrow

There it is you are supposed to leave those on the only state that could be disabled is C&Q cool and quiet and it doesn't need to be either you can leave all the c -states on and carry on with a OC

anyway there is your issue leave the power states on take off turbo leave on llc and adjust to 1.476 you should see a big drop in temps

Nope. Fails at Intel. I'll try bone stock. Again. Otherwise I think its the board. I'm calling Asus and raising hell tomoroow. This is my 5th freaking board from them. BS now

Solarstarshines said:

N00berG00ber said:

Solarstarshines said:

there is something wrong do you have any power states disabled ?

I disabled everything.

I've tried with c6 enabled and disabled. Dosent make a difference.

I'm flashing and older bios version now.....

I personally think the board is messed up. i think i see a long very angry talk with asus tomorrow

There it is you are supposed to leave those on the only state that could be disabled is C&Q cool and quiet and it doesn't need to be either you can leave all the c -states on and carry on with a OC

anyway there is your issue leave the power states on take off turbo leave on llc and adjust to 1.476 you should see a big drop in temps

I've tried. Freezes and crashes.

It seems fine with all stock settings. I'll let it run some more.

So now then comes a question. Leave it at 4.6 and. .476v and call it quits or call Asus and try to get something else? This would be my 6th RMA for this board.

Wait, You have had the same issue with 5 Mobo's? Makes if FAR less likely to be a Mobo issue in that case.

Sounds like incorrect setting in that case.

N00berG00ber said:

It seems fine with all stock settings. I'll let it run some more.

So now then comes a question. Leave it at 4.6 and. .476v and call it quits or call Asus and try to get something else? This would be my 6th RMA for this board.

If my 8350 ran 4.8 at that voltage im sure your should be able to use lower at that speed but that voltage 1.476 is the sweet spot for 4.7 you might be able to lower it more but if you are cool with those volts then go right ahead

E=gaia;2555573]Wait, You have had the same issue with 5 Mobo's? Makes if FAR less likely to be a Mob. issue in that case.

Sounds like incorrect setting in that case.[/QUOTE]

No first board with this issue. OK prime is running fine with stock settings.

Heres what i change

Air over clock tuner = manual
CPU ratio - 23
Turbo core disable
CPU/nb freq- 2200mhz
Ht link 2400mhz
CPU load line calibration - enabled
CPU offset voltage - .043750
Cool and quiet - disabled
C1e - disabled
Svm- disabled
Core c6 state - disabled
APM master mode - auto
HPC - disabled.

Ok this guy is overclocking with your board look at what he is doing and compare your settings maybe you will see something you are doing wrong