Would like to have some opinions

Page 13 of 24 FirstFirst ... 3111213141523 ... LastLast

  1. Posts : 26,745
    Windows 11 Pro
       #121

    Jack, you may check, but I've always thought the PSU fan was intake and blows hot air out of the back of the case. Positive air pressure is very good. I have all my fans as intake except the rear exhaust. It works well for me. That ram is what I'm using as well as several others here. It's very good ram, as far as I'm concerned. Great build though. I wish I had the money for a 2011 build. But it's a little rich for me right now. Maybe a little later though. Also, if you get energetic, would you measure how far from the top fans on the bottom of your rad to the top of the motherboard. Your Rad is 46mm thick and your'e running push/pull. My rad is 66mm thick and I don't have a case I can run push/pull. I was hoping that case would do it. It looks like you have a good space in there. I would need right at 1" more than you do. My Switch 810 and the HAF X are both about 5 or 6 mm too short. I always get the VRM and the ram in the way. If you don't feel up to it, don't bother. I'm getting the case either way Already ordered as soon as Amazon gets them in.
      My Computer


  2. Posts : 25,847
    Windows 10 Pro. 64/ version 1709 Windows 7 Pro/64
    Thread Starter
       #122

    Thank you for taking care of my brain fart. I don't know what I was thinking.
    All power supplies blow out the back where the cord attaches. At least all I have ever seen.
    Took care of the problem by putting the filter back where it should be by the power supply and took the one from the other 2 fan area on the same side panel and used it on the back.
    Another thing I would like to see this case have is a push button of some sort to remove the side panels.
    I have had my side panels on and off several times.

    As for the room for push/pull their is about a 1 1/2 from the fans
    I have installed to the ram. I held a 120 mm fan in a push/pull and there was about 1/2 in. to the ram.
    The radiator sits in the case far enough to the glass panel side that the fans will drop down and leave about 3/8 in. between the side of the fan and VRM.

    I do believe you could install the second set of fans under the top cover. I used a 120mm fan that measures 1 in. thick and put it in all 3 positions under the top cover and it the cover would shut with no bulge and no extra pressure.
      My Computer


  3. Posts : 26,745
    Windows 11 Pro
       #123

    Sounds great, Jack. Thanks a lot for checking for me. I appreciate it.
      My Computer


  4. Posts : 25,847
    Windows 10 Pro. 64/ version 1709 Windows 7 Pro/64
    Thread Starter
       #124

    Your very welcome!!
      My Computer


  5. Posts : 24,479
    Windows 7 Ultimate X64 SP1
       #125

    Jack that is an awesome looking build mate! Tidy cabling on the "dirty" side of the case too.
    I'm with Steve on the Trident X RAM, I have a 16GB set and it is fast.
      My Computer


  6. Posts : 5,915
    Windows 10 Pro X64
       #126

    I have to say, that is a great looking build Jack
      My Computer


  7. Posts : 24,479
    Windows 7 Ultimate X64 SP1
       #127

    Slow down Jack if you have a sweaty spot.
      My Computer


  8. Posts : 9,612
    Win 7 Ultimate 64 bit
       #128

    Britton30 said:
    Slow down Jack if you have a sweaty spot.
    An antiperspirant would help.
      My Computer


  9. Posts : 25,847
    Windows 10 Pro. 64/ version 1709 Windows 7 Pro/64
    Thread Starter
       #129

    I found a new sweat spot under 1.30V Vcore.
    100% load Prime 95
    Max. temps 61C.

    Would like to have some opinions-29cw6z.png
      My Computer


  10. Posts : 6,077
    Windows 7 Professional 64 bit
       #130

    Much better voltage, nice work.
      My Computer


 
Page 13 of 24 FirstFirst ... 3111213141523 ... LastLast

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd
All times are GMT -5. The time now is 22:01.
Find Us