New
#1
System Freezes and not stable after installing Crosshair RAM?
I am getting a 30 second freeze after installing new RAM and sometimes a BSOD with memory code 0x00000f4
This is my system specs and its all new, i replaced everything within the past month so Im pretty sure its not a comopnant fairure but an installation failure. (yes I checked everything is connected to the MB properly)
MB is
Gigabyte MB GA-B85M-D3H - This board supports DDR3 and XMP
http://download.gigabyte.us/FileList...b85m-d3h_e.pdf
RAM is
Crosshair Vengance DDR3 2x4GB - 1600Mhz - Corsair CMZ8GX3M2A1600C9B 8GB 1600Mhz CL9 DDR3 Vengeance Memory Module Kit
Corsair CMZ8GX3M2A1600C9B Vengeance 8GB (2x4GB) DDR3 1600 Mhz CL9 XMP Performance Desktop Memory Kit Blue: Amazon.co.uk: Computers & Accessories
CPU is
CPU - Intel Core i5 4440 Quad Core CPU Retail (Socket 1150, 3.10GHz, 6MB, 84W, Extended Memory 64 Technology
Power is Crosshair 750w
The newley installed RAM is running at 1333MHz which might be the reason for the freezes. I took a look in the bois with the help of the manual but I couldent figure out what to set or change .
My questions are ......
1) What is XMP profile 1 and should I set up XMP - and if so will it help. I think the bois is using the JEDEC timings? I got the following from CPUz
JEDEC timings table CL-tRCD-tRP-tRAS-tRC @ frequency
JEDEC #1 6.0-6-6-17-22 @ 457 MHz
JEDEC #2 7.0-7-7-20-26 @ 533 MHz
JEDEC #3 9.0-9-9-25-33 @ 685 MHz
And aslo this information ? Im clueless as to what it means or how it should be set?
Chipset
-------------------------------------------------------------------------
Northbridge Intel Haswell rev. 06
Southbridge Intel ID8C50 rev. 04
Memory Type DDR3
Memory Size 8 GBytes
Channels Dual
Memory Frequency 665.1 MHz (1:5)
CAS# latency (CL) 9.0
RAS# to CAS# delay (tRCD) 9
RAS# Precharge (tRP) 9
Cycle Time (tRAS) 24
Row Refresh Cycle Time (tRFC) 174
Command Rate (CR) 1T
Uncore Frequency 1396.7 MHz
MCHBAR I/O Base address 0x0FED10000
MCHBAR I/O Size 19456
MCHBAR registers
Memory SPD
-------------------------------------------------------------------------
DIMM # 1
SMBus address 0x51
Memory type DDR3
Module format UDIMM
Manufacturer (ID) Corsair (7F7F9E0000000000)
Size 4096 MBytes
Max bandwidth PC3-10700 (667 MHz)
Part number CMZ8GX3M2A1600C9
Manufacturing date Week 22/Year 12
Number of banks 8
Nominal Voltage 1.50 Volts
EPP no
XMP yes
XMP revision 1.3
AMP no
JEDEC timings table CL-tRCD-tRP-tRAS-tRC @ frequency
JEDEC #1 6.0-6-6-17-22 @ 457 MHz
JEDEC #2 7.0-7-7-20-26 @ 533 MHz
JEDEC #3 9.0-9-9-25-33 @ 685 MHz
XMP profile XMP-1600
Specification PC3-12800
Voltage level 1.500 Volts
Min Cycle time 1.250 ns (800 MHz)
Max CL 9.0
Min tRP 11.25 ns
Min tRCD 11.25 ns
Min tWR 15.00 ns
Min tRAS 30.00 ns
Min tRC 41.25 ns
Min tRFC 260.00 ns
Min tRTP 7.50 ns
Min tRRD 6.25 ns
Command Rate 2T
XMP timings table CL-tRCD-tRP-tRAS-tRC-CR @ frequency (voltage)
XMP #1 6.0-6-6-16-22-2T @ 533 MHz (1.500 Volts)
XMP #2 9.0-9-9-24-33-2T @ 800 MHz (1.500 Volts)
DIMM # 2
SMBus address 0x53
Memory type DDR3
Module format UDIMM
Manufacturer (ID) Corsair (7F7F9E0000000000)
Size 4096 MBytes
Max bandwidth PC3-10700 (667 MHz)
Part number CMZ8GX3M2A1600C9
Manufacturing date Week 22/Year 12
Number of banks 8
Nominal Voltage 1.50 Volts
EPP no
XMP yes
XMP revision 1.3
AMP no
JEDEC timings table CL-tRCD-tRP-tRAS-tRC @ frequency
JEDEC #1 6.0-6-6-17-22 @ 457 MHz
JEDEC #2 7.0-7-7-20-26 @ 533 MHz
JEDEC #3 9.0-9-9-25-33 @ 685 MHz
XMP profile XMP-1600
Specification PC3-12800
Voltage level 1.500 Volts
Min Cycle time 1.250 ns (800 MHz)
Max CL 9.0
Min tRP 11.25 ns
Min tRCD 11.25 ns
Min tWR 15.00 ns
Min tRAS 30.00 ns
Min tRC 41.25 ns
Min tRFC 260.00 ns
Min tRTP 7.50 ns
Min tRRD 6.25 ns
Command Rate 2T
XMP timings table CL-tRCD-tRP-tRAS-tRC-CR @ frequency (voltage)
XMP #1 6.0-6-6-16-22-2T @ 533 MHz (1.500 Volts)
XMP #2 9.0-9-9-24-33-2T @ 800 MHz (1.500 Volts)
2)Can anyone give me step by step instructions on how to set this RAM to make my system stable.
Thank you I would be very graftful for any feedback